9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
I had two extension springs replaced, all for $135.00 (this included tax). The work took about 35 minutes and I was relieved to have this taken care of. You never realize the importance of something to you, until it is broken. Was this a good price? Seemed reasonable enough and the repairman came out the same day I called. Harris County Houston, Tx.
10.1 It is now time to wind the new springs, but before doing so, I recommend marking the shaft just beyond the winding cone. This is a final step taken to assure that you have installed the springs on the correct sides of the center bracket. Torsion springs always grow in length when they are wound in the proper direction. If your spring does not get longer as you wind it, you are winding it the wrong direction probably because it is improperly installed. We recurrently get calls about springs coming loose from the cones at about 6 turns. If this happens, switch the springs.
Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.
As commercial and residential garage door service professionals, we’ve pretty much dealt with every issue you can think of when it comes to garage door repair. Even still, there are sometimes issues that continue to surprise us, like the tiny insect nest growing on the photo eye sensor or the tennis ball that somehow managed to knock the door entirely off its track. Even though these issues are uncommon, it’s nothing that garage door service professionals like us can’t handle!
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
My experience with Overhead Garage Door was exceptional! They were friendly and fast! I didn’t have to wait days to hear back from them and their prices were far better than that of their competitors top article. I would highly recommend Overhead Garage Door to anyone needing assistance with their door and especially if you’re in the market for a new one!
11.2c If the springs you installed are too weak, and you wind the springs the correct number of turns, the door will be heavy at the floor, and it will not stay open half way, but it will stay open if raised completely. If tension is added to the torsion springs to lighten the garage door and to get it stay open half way, the door will be harder to close; openers often damage the new steel garage doors when they are too hard to close.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
At DIY Garage Door Parts, we help you identify the problem and the solution. We help you find and order the right parts and tools (torsion springs, winding bars, extension springs, rollers, garage door parts, opener/operator parts, and accessories). We ship the parts on the same day or next business day. And we guide you through the process on how to repair your broken garage door springs with video tutorials and phone support. Whether you are learn how to repair a broken garage spring, and wanting to change your worn out rollers to make your door super quiet, our video library has everything you need to show you whatever garage door fix you may need. You can bring your laptop or mobile device right to your garage and learn how to fix your broken garage door springs – correctly and safely – while you watch a how to video! http://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]
The national average for garage door repair cost is between $80 and $110. Some of the factors that affect your garage door repair cost are the type of springs (most often torsion or extension), the size and weight of the door, and the door material. Many garage door pros will charge a service fee to visit your house and determine the problem. Often, the service fee includes a set amount of labor. One example of this is an $80 service fee that includes the first hour of work plus testing and inspecting your garage door and garage door opener, while another pro may charge $150 for the same standard service call.   
We offer industry leading service performed by the best licensed professionals in the region. Whether you need springs replaced, a motor repaired or need a new panel on your door, our service workers will get the job done efficiently and effectively, ensuring that your door is back in working order as soon as possible. We also offer a wonderful preventative maintenance program. This is a cost effective way to ensure that you avoid future problems by having the small, unnoticed issues addressed right away.
Lewis did a great job and not only met my expectations but blew them away. His attention to detail was impressive. He reolaced the springs on my two car garage door and he went out of his way to adjust the tension on my second single car garage door to make it open better. He also recommended replacement of the rollers on my main garage door as they were getting pretty worn out and making some noise. He was very friendly and personable. Was willing to explain what he was doing so we could learn something too. I would recommend Lewis Nagy if you are in his area here in Apollo Beach/Riverview. Thanks again!

8.10 Double-check to make sure you have the correct wind on your new torsion spring. On the left side next to the winding cone the end of the spring wire should be pointing up if it is facing you. Notice, also, that the cone is red which usually designates right wind. Customers frequently call and explain that when they get about six turns on the springs they spin on the cones. This is due to installing the springs on the wrong sides of the center bracket.
One of the best ways to care for your springs is to check them over for wear. You can certainly look at them for damage, but sometimes the damage isn’t something that’s visible. In these cases, try lifting the garage door up from the ground. About halfway up, let go. If the door stays, the springs are still working perfectly. If the door sags or drops at all, this could be a sign that your springs are beginning to weaken and will need replacing soon.
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.
Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working. 

Texas Garage Door and Opener in Plano, TX provides residential garage door and commercial overhead door services throughout Dallas, Fort Worth and the surrounding areas. Our fully insured team specializes in garage door installations, repairs and maintenance services. We have over 25 years of combined experience and qualified technicians ready to service your garage door needs. We are available 24/7 for emergency service, please call 972-633-3872 today!
There’s never a convenient time for your garage door springs to break. When this crucial component gives out, you need a repair job or replacement as soon as possible. That’s why Marvin’s Garage Doors is available 24/7 for emergency service. When that emergency arises, or you’re stuck in your garage and unable to get out to get to work, simply give us a call on our emergency line at 336-813-2601.
Step 2: Check the tracks with a level to make sure they're properly aligned. Horizontal tracks should slant slightly down toward the back of the garage; with roll-up doors, the vertical sections of track should be exactly plumb. Both tracks must be at the same height on the garage walls. If the tracks are not properly aligned, loosen but do not remove the screws or bolts that hold the mounting brackets, and tap the tracks carefully into position. Recheck the tracks with the level to make sure they're in the right position; then tighten the screws or bolts at the mounting brackets.
First and foremost, a garage door, by design, contains springs designed to balance your door and make it easier to lift. Those springs are under incredible amounts of tension. If a spring breaks or is improperly released, it can cause incredible and potentially fatal injuries. Keep in mind, when working on a garage door spring, it is likely that your face and head will be close to it, meaning that your most sensitive area will be in the direct path of the released spring.

Abc Garage Door Repair Centennial Colorado 80016


We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
×