Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.
If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.
Because your garage door is a major entryway to your home, it is important to keep it in good working order for your own safety, security, and convenience. Choosing the right style and appropriate materials will lessen the amount of repairs that may arise. Additionally, investing in regular maintenance can be cost-effective in the long run. If your garage door is in need of major repair, it is best to call a professional garage door repair company for assistance. Typically, the company will charge for at least one hour for making a service call. However, the benefits of a professional repair job can well outweigh any costs, as a professional can ensure the safety, security, and proper operation of your garage door.

A1 Garage Door Repair Centennial Co 80016


I told several people that I planned on installing a garage door torsion spring after mine broke. ALL of them told me that it was too dangerous and a few feared for my life! Honestly it was one of the simplest home repairs I have ever done. That is thanks in large part to your very helpful installation video. Your videos on measuring springs etc. were also very helpful. All of the necessary details are there.

Garage Door Repair Companies Centennial Co 80015


There’s never a convenient time for your garage door springs to break. When this crucial component gives out, you need a repair job or replacement as soon as possible. That’s why Marvin’s Garage Doors is available 24/7 for emergency service. When that emergency arises, or you’re stuck in your garage and unable to get out to get to work, simply give us a call on our emergency line at 336-813-2601.
In order to replace your garage door spring(s), you will need to find the current measurements in order to accurately replace the spring(s). This should take about 3 minutes and you don't need to remove the springs or loosen the tension to measure them. Our springs are made to be a bit flexible, so you don't have to get it to an exact measurement. 
Insulation increases the efficiency of your door and can lower your electric will. You need R-value garage doors. These type of doors keep out hot and cold air and also provide a sound barrier between the outside and your garage. Insulated doors use polyurethane or polystyrene foam as insulation inside the door. More information about garage door replacement cost.
Home Depot local Service Providers are background checked, insured, licensed and/or registered. License or registration numbers held by or on behalf of Home Depot U.S.A., Inc. are available at homedepot.com/licensenumbers or at the Special Services Desk in The Home Depot store. State specific licensing information includes: AL 51289, 1924; AK 25084; AZ ROC252435, ROC092581; AR 228160518; CA 602331; CT HIC.533772; DC 420214000109, 410517000372; FL CRC046858, CGC1514813; GA RBCO005730, GCCO005540; HI CT-22120; ID RCE-19683; IA C091302; LA 43960, 557308, 883162; MD 85434, 42144; MA 112785, CS-107774; MI 2101089942, 2102119069; MN BC147263; MS 22222-MC; MT 37730; NE 26085; NV 38686; NJ 13VH09277500; NM 86302; NC 31521; ND 29073; OR 95843; The Home Depot U.S.A., Inc. is a Registered General Contractor in Rhode Island and its Registration Number is 9480; SC GLG110120; TN 47781; UT 286936-5501; VA 2705-068841; WA HOMED088RH; WV WV036104; WI 1046796.
On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.

The most common question we get over the phone is, "Okay, so how much does it cost to replace garage door springs?" To give you an exact price quote, we would need to know the size of the door, weight, and type of garage door springs needed (torsion or extension). Since we carry over 30 different types of springs to account for all the different types of garage doors, we recommend that a certified technician takes the proper measurements himself before giving you an exact price quote.


A1 Garage Door Service is known for providing only the best value for money. We always aim for the best possible customer service and experience, reasonable costs for our products and services, give FREE estimates and FREE professional advice as well as amazing deals and discounts when you book our service. What’s more, we GUARANTEE that we service all manufacturer warranties, including lifetime warranties. What more can you ask for?
However, if you lose power and use the disconnect switch, you’ll need to reattach it to use your garage door motor to open and close your door again. Open the door all the way and then reattach this hook. Then try opening or closing the door again with your transmitter, and you should be all set. It will be easiest to reattach this hook when your car is not in the garage, as you’ll need to place a step ladder underneath the motor to reach it.
There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.

7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.
I was having trouble with my old garage door and decided that it was finally time to get a new one. I called Overhead Garage Door after a friend recommended them to me and I couldn’t be happier with the results. Overhead Garage Door was at my house immediately and the service was very professional and thorough. I would highly recommend this company to anyone who is looking for a new garage door or needs repairs done. I will definitely be using them in the future.

Garage Door Repair Estimates Centennial Colorado 80015


If your garage door isn’t operating properly, the torsion springs are likely to blame. If you’re concerned about tackling this project on your own, consider hiring out the job to a professional. Otherwise, replace both the left and right springs at the same time to save yourself from having to do the job twice. Remove the old springs and measure them while they’re relaxed. Only then will you be able to order replacement parts and install the new springs. Replacing your own garage door springs takes only a little time and effort and can save you hundreds of dollars.


Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.

Garage Door Repair Free Estimate Near Me Centennial Colorado


My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself.
Guest 9232954 -- check out the other answers for this question, and the links below the answers for even more - seems from $125-400 range from different contributors (should be replaced in pairs for balanced lifting unless one spring is quite new), about $200-250 or 300 seems a common charge. The springs themselves generally run about $20-50 each depending on lead they have to carry.
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
Professionals can replace garage door springs in an hour or two. When you hire a pro, make sure to ask about the quality of the springs they will install. They may well offer several grades of springs to choose from, at a range of costs. Top of the line springs may be guaranteed for life, while economy springs can be expected to last perhaps five years under normal use.
If your garage door track is out of alignment, it can be a serious issue. The metal track your door runs on needs to be aligned properly in order for your door to move. If you see gaps between the rollers and rail, or bends in the rails themselves, you have a problem. The heavy weight of the door can compound these issues and make them worse until it becomes dangerous to operate your door.
Doors with extension springs have two sets of pulleys (which are sometimes called sheaves): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
×