Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
If you can hear your garage door motor running for what seems like the full amount of time it normally would take to open or close the door, but the door doesn’t move, chances are the disconnect switch has been enabled. Every garage door opener comes with a disconnect switch in case you lose power. This allows you to open or close the door manually so your car isn’t stuck in the garage until the power comes back on. http://www.youtube.com/v/Z_eZc-kh40c&feature=youtube_gdata
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

Garage Door Repair Free Quote Centennial Colorado 80016


Garage door springs don’t require extensive care and maintenance. However, they also can’t be left entirely to their own devices. Spraying the springs with WD-40 is a good place to start. It’s also a good idea to check the balance of the garage door every year. To do this, simply lift the garage door up about halfway and let go. If the springs are in good working condition, the door should remain still. If the springs are beginning to weaken, the door might sag or fall. By taking these basic steps, you can preserve your door springs for longer.
Professionals can replace garage door springs in an hour or two. When you hire a pro, make sure to ask about the quality of the springs they will install. They may well offer several grades of springs to choose from, at a range of costs. Top of the line springs may be guaranteed for life, while economy springs can be expected to last perhaps five years under normal use. 

If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own. http://www.youtube.com/embed/Z_eZc-kh40c
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

Garage Door Repair Free Estimate Centennial Colorado


Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.
There are lots of ways your garage door can suffer damage. The tracking might be rusted or broken, the weatherstripping might need to be replaced or the door itself might actually be broken or have a hole in it. After all, garage doors are sturdy but not unbreakable. One component of your garage door in particular that will likely need replacing every so often is the spring.

At DIY Garage Door Parts, we help you identify the problem and the solution. We help you find and order the right parts and tools (torsion springs, winding bars, extension springs, rollers, garage door parts, opener/operator parts, and accessories). We ship the parts on the same day or next business day. And we guide you through the process on how to repair your broken garage door springs with video tutorials and phone support. Whether you are learn how to repair a broken garage spring, and wanting to change your worn out rollers to make your door super quiet, our video library has everything you need to show you whatever garage door fix you may need. You can bring your laptop or mobile device right to your garage and learn how to fix your broken garage door springs – correctly and safely – while you watch a how to video! http://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.

Garage Door Repair Free Quote Centennial 80016


11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.
Plus, we carry all the best and high quality products from the top garage door brands. Whatever is your requirement or need for your garage door, we are sure to have them in our comprehensive inventory. We have garage doors in different styles, materials, colors, designs and what-have-you. If you still cannot find what you are looking for, we can always source them out for you.

Automatic Garage Door Repair Centennial Co


Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.

Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
Garage door springs can —and will—break, and if you're anywhere near the garage when this happens, you'll know it. Nothing else sounds quite like a giant metal spring snapping under tension. Even if you don't hear it, you'll know the spring broke as soon as you (or your garage door opener) try to lift the door and finds that it now weighs twice as much. So faced with a broken garage door spring, the question is, can you fix it yourself?

Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.


Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.

Garage Door Repair In My Area Centennial Co 80016


When a company tells you they're providing you a warranty of only 1-3 years, it means they could be using cheap hardware. We can provide a lifetime warranty on the hardware we use because it's superior to a traditional garage door company's hardware in a number of ways. We're so confident that our springs won't need replacing, if by chance one DOES break, our name is on the springs to remind you to call us to replace it for free!

Garage Door Repair How Much Centennial Co 80016


Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2]

Founded in 2011, Overhead Garage Door, LLC is a rapidly-growing garage door repair and installation company headquartered in Fort Worth, Texas. We serve both commercial and residential markets, and believe in the value of hard work and craftsmanship. We are fully licensed and insured and offer a broad selection of products to suit our customer's needs. As a family-owned and operated business, we put unbeatable customer service above all. This belief has allowed us to routinely expand into new markets and locations as we improve quality control and customer satisfaction.


Garage doors make life easier, particularly when you’re arriving home in the middle of a rainstorm. It’s easy to take the convenience a garage door provides for granted -- until it stops working properly. The door loses its visual appeal instantly, stuck there half-open. This type of situation also raises security concerns as a simple trip to the store can become a headache. Simple fixes when a garage door gets stuck halfway may prevent it from happening again.
• Extension springs: Garage door extension springs stretch to provide lifting power for the door. These springs are typically made of steel and mounted above the horizontal track of the garage door. A safety cable should run through your extension springs to prevent possible injuries or property damage. Extension springs are the most common type of garage door spring for residential use and can break after excessive usage.

Garage Door Repair Estimates Centennial Co


CAUTION! Replacing garage door torsion springs is dangerous because the springs are under tension. If you do not use the right tools and follow safe procedures, you could lose hands, limbs or even your life. You could also damage property. We want your business, but not at the expense of your well being. Doing the job right is your responsibility. If you have any doubts about your ability to safely change your springs, we recommend you hire a professional to repair your garage door. Safety First! Then work.

Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]

Garage Door Repair And Installation Centennial 80016


Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break. http://www.youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!! https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.

A1 Garage Door Repair Centennial Colorado 80015


Garage doors are able to move due to a counterbalance system that usually consists of a torsion spring. We often find incorrect springs have been installed which result in an unsafe door that you may not be able to open manually when needed. The balance of your garage door should be tested annually to reduce wear on your garage door opener and ensure it can be opened if an emergency situation arises. Because of the dangers involved with torsion springs, garage door spring repair and installation should only be done by experienced professionals like our Medics.
×