One of the large springs on our garage door broke the day before Thanksgiving, trapping our van inside the garage. We have a daughter in a wheelchair and had lots of errands to run before Thanksgiving, so we really needed our van. We called Overhead Garage Door and they told us approximately when they would arrive. They not only replaced the broken spring, they replaced the other spring, all of the rollers and most of the hinges. They also replaced several rollers and hinges on the second garage door. The technician, Micah, and his brother could not have been nicer. The garage doors have never worked as well or been this quiet. I highly recommend Overhead Garage Door to anyone in need of new garage doors, or repairs to existing doors. A first class business.
Garage door torsion springs are usually the first to break or give out among the many components of your garage door. This is because the springs bear a lot of pressure, supporting the entire weight of your garage door which can oftentimes be quite heavy. Through regular and continued use, garage door springs are usually stretched tight and subject to wear and tear.
Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.

Garage Door Repair Free Estimate Near Me Centennial Colorado


DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

A1 Garage Door Repair Centennial Colorado 80016


Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.

Abc Garage Door Repair Centennial Colorado 80015


SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.
Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done. 

Garage Door Repair Free Estimate Centennial Colorado


A garage door with aging springs puts an enormous load on a garage door opener, so another sign of failing springs is when you hear the electric door opener begin to strain as it attempts to lift the door. At this point, it is time to consider replacing the springs. Aging door springs can also break suddenly, a situation that can cause the door to slam shut violently. If you happen to be present when a spring breaks, you will hear a very loud sound like a gunshot, because the break usually occurs when the spring is fully loaded—stretched or twisted to its full tension. When one spring breaks, the door will suddenly feel very heavy when you try to open it by hand, and an automatic garage door opener may no longer be able to lift the door at all. https://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.


Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.
Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.
Garage door springs offset the weight of a garage door and allow the door to be opened and closed easily, either by hand or by an automatic garage door opener. The high-tension steel in the springs has a limited lifespan, and over time, the springs lose their effectiveness. Garage door springs come in levels of quality—they may be described as "10,000-use" or "20,000-use" springs, for example. This may sound like a very large number, but when you consider that a garage door might be opened four or five times a day, every day, every year, it becomes clear that there is a limited lifespan for these critical garage door parts.

Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
From a big-box store, basic garage door cables can run between $8 and $20, depending on the product. Your pro may charge you a different cost if they provide the cables. Your cables may not need to be replaced if they have simply come off the track, but broken cables will need to be completely removed and replaced. In either instance, the pros will need to secure or take down the door; unwind the springs; reset or replace the rollers, cables, and drums; and then wind the springs once more. For example, a pro could reset cables that have come off the track for $129.99. The average national cost for a garage door repair specialist is $80 - $110 per hour and the typical cost to replace a broken garage door cable is anywhere from $130 to $200.
Poor lubrication is a very common and easy to fix explanation for why you might find your garage door stuck. You should properly lubricate your garage door's track, the opener chain and the springs every few months as part of regular preventative maintenance. Be sure to use Clopay's Garage Door ProLube or sillicone based lubricants. Do not use WD-40.
I've been watching TOH since 1981. I just happened to stumble across it on PBS during a repeat of the second season, was instantly taken with it - and, hooked-for-good. That particular show/season (the Newton/ H. H. Richardson House - 1981) remains my favorite. Also, I happened to meet Norm quite a few years back and he mentioned it as being his favorite, as well - all-the-more reason for me to have fond memories of it. If I were to pick more 'favorites' from the 'Bob-era', 'Steve-era' and 'Kevin-era' they would be: 'Bob-era' - the Lexington Bed & Breakfast (1988) and the In-and-Around Boston shows (1984); 'Steve-era' - the Concord Barn (Wickwire House - 1989), the Wayland House (Kirkside - 1991)) and the Jamaica Plain House (1990); 'Kevin-era' - the Cambridge House (2005), the Newton Shingle-style House (2007) and the Detroit Houses (2017).p.s. - I've very much enjoyed the times that the show has gone back and looked at previous projects. It's always nice to see how the home - and homeowners - have done over time. Thank you! https://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
The springs are an essential component to your garage door in that they enable the door to be lifted or lowered easily, despite its weight. If either of the springs are broken, then the door will become stuck. There are two types of garage door springs – torsion springs and extension springs. Torsion springs are located near the top of the door, whereas extension springs are located on each side of the door. If your garage door uses torsion springs, check for a gap between the springs to identify whether they are broken. If you have extension springs, look to see if a piece of the springs are hanging from the side.
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.
When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.

The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs. https://www.youtube.com/v/Z_eZc-kh40c?version=3
We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.

Garage Door Repair Guy Centennial Colorado 80016


9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.
Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.

Automatic Garage Door Repair Centennial Colorado 80015


Examine the garge door rollers, hinges, tracks, and other hardware for signs of damage that might cause the door to hang up. Lubricate the tracks and hardware with silicone spray or oil. Raise the door slowly, watching it as it lifts. See if it catches on a warped panel or support beam or if an obstruction in the path of the photo eye causes it to stop or reverse. Any part that protrudes into the path of the garage door can cause it to stop.
11.2a Raise the garage door slowly. Check the door balance. If you have the correct springs the door should stay down when closed, half way when opened half way, and open when opened. If the door will drop to the floor by itself from the halfway point, add 1/4 turn of tension to each of the torsion springs. If the garage door won't stay on the floor, and if it pulls itself up when stopped halfway, close the door and remove 1/4 turn of tension from the springs.

Snap a locking pliers onto the torsion tube to lock it into place while you tighten the drums. Rotate the drum to wind the cable into the winding grooves. Pull the cable as tight as possible before tightening the setscrews. Leave the locking pliers in place and repeat the tightening procedure on the other side. You want equal tension on both sides. Otherwise, the door will open unevenly.
Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner. http://youtube.com/watch?feature=youtu.be&v=Z_eZc-kh40c
Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
Whether you're planning on moving in the future or you're fixing up your forever home, replacing a garage door can provide an excellent return on investment and boost your home's resale value. According to Remodeling magazine's 2016 Cost vs. Value report, garage door upgrades provide a nationwide average return on investment of over 90%, making it one of the top five home improvement projects. To learn more about the cost of installing garage doors, visit our garage door and opener installation and repair cost guide.
To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.

Abc Garage Door Repair Centennial Co 80016


If this is the problem then you will be able to tell by seeing if your garage door rollers are literally off track. If your garage door panels are not damaged, then you do not need to replace your door. However, the rollers do need to be put back on the track which should be done by a professional. If you are looking for a garage door company that specializes in Garage Doors, Garage Door Repair, or Garage Door Openers, or are just looking for more information, please visit our website at precisiondoor.net. Remember, "We Fix Garage Doors Right"™.

Examine the garge door rollers, hinges, tracks, and other hardware for signs of damage that might cause the door to hang up. Lubricate the tracks and hardware with silicone spray or oil. Raise the door slowly, watching it as it lifts. See if it catches on a warped panel or support beam or if an obstruction in the path of the photo eye causes it to stop or reverse. Any part that protrudes into the path of the garage door can cause it to stop.
If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.

Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly.

Garage Door Repair Estimates Centennial Colorado 80016


Maybe the battery died or a spring broke, but you can't get into the garage to even see what the problem is. If the garage door is the only way in or out, or if you can't find the key to the door, you'll have to either find a way to break in or call a locksmith. As a preventative measure, it's smart to keep a spare key or install an emergency key release that would allow you to release the emergency disconnect to the operator so you can manually raise the door.
We offer industry leading service performed by the best licensed professionals in the region. Whether you need springs replaced, a motor repaired or need a new panel on your door, our service workers will get the job done efficiently and effectively, ensuring that your door is back in working order as soon as possible. We also offer a wonderful preventative maintenance program. This is a cost effective way to ensure that you avoid future problems by having the small, unnoticed issues addressed right away.

Locating a contractor - there are many professional overhead garage door companies. It is always advisable to contact at least three different agencies and request a bid or quote for the work. Be sure that each quote includes the costs for a few different types of doors, any installation fees, and the cost of wiring the electronic openers. Standard prices range from:


When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.

Garage Door Repair Near Me Centennial Co


6.1 It is time now to unwind the old spring that is not broken. A few warnings are in order. NEVER, NEVER, NEVER touch a set screw without first inserting a properly fitting bar into the winding cone! Also, do not use box or socket wrenches for the set screws. If the cone slips, the wrench could break your hand in 10 spots before unwinding completely. It's my guess that this is the number one cause of trips to the emergency room for inexperienced homeowners fixing or replacing their springs.

Garage Door Repair Guy Centennial Colorado 80015


I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:


You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
Founded in 2011, Overhead Garage Door, LLC is a rapidly-growing garage door repair and installation company headquartered in Fort Worth, Texas. We serve both commercial and residential markets, and believe in the value of hard work and craftsmanship. We are fully licensed and insured and offer a broad selection of products to suit our customer's needs. As a family-owned and operated business, we put unbeatable customer service above all. This belief has allowed us to routinely expand into new markets and locations as we improve quality control and customer satisfaction.

2.1 Two important assumptions will help you execute this replacement safely. First, assume that the springs are going to break as you unwind or wind them. To avoid injury, clutch the bars firmly on the ends furthest away from the cones and stand securely on a sturdy ladder, not on chairs or cans turned upside down. Keep clothes and body parts away from the springs. Wear safety glasses.
Like any mechanical part, garage door springs deteriorate due to normal wear and tear. Over time, the steel that makes up the springs weakens until they eventually break. Under normal circumstances, garage door springs have a life expectancy of 10,000 cycles of opening and closing. This equates to five to seven years, but along the way, there may be signs of problems that can occur before the springs actually stop working.

6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
×