In order to prevent injury, garage doors automatically reverse if they come into contact with an obstacle. When the door closes halfway but then reverses for no apparent reason, this may be a sign that there is something preventing it from closing, something that you can't see. Check the tracks for stuff like dirt, rocks, bits of trash, or other debris. Give the tracks a wipe-down to dislodge anything that might be getting in the way.


To evaluate whether the problem lies with the door or the automatic opener, make sure the door is in the fully closed position, then disengage the opener trolly from the door by pulling the emergency release cord. Try to lift the garage door by hand. If the door opens smoothly by hand, the problem is with the opener. If the garage door still only opens halfway, the problem is with the door.

Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!! https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c


Every modern garage door is built with a sensor due to a mandate passed by the government back in the 1990’s that required garage door opener manufacturers to install safety devices. To meet this mandate, most garage doors have a sensor installed on each side of the doorway. They are often referred to as photo eyes since their main function is to maintain visual contact with one another. If that visual contact is broken by an obstruction, then the garage door stops in its tracks. This is meant to prevent the garage door from closing on a vehicle – or even worse, a person.
9.16 If you cannot get the stationary cones to finger-tighten against the center bracket, we recommend installing washers between the winding cone that houses the bearing and the spring bracket. This is a common problem with torsion springs on older Windsor garage doors because their steel bearings are often wider and they extend beyond the stationary cone. Raynor garage doors also have wider bearings that fit properly in their 2 1/4" stationary cones, but washers may need to be installed if their bearings are installed in 1 3/4" or 2" stationary cones, or if some of their older bearings are installed in their newer cones that are installed on older brackets.
Torsion springs are located above the opening of your door with springs slid onto a bar. Extension spring systems can be found alongside the opening of the door. It's important to know whether or not a garage door company provides service for your needs. Precision 's certified technicians are fully equipped to work on torsion and extension spring systems.

Garage Door Repair Free Quote Centennial Colorado


Since 1998, our clients have always been our top priority. That is why we strive to ensure efficiency and reliability in all our services. This is evidenced by our consistent Yelp 5 Star rating, A+ rating from BBB and Super Service Award from Angie’s List. You can trust that our work is done with quality as we are licensed, bonded and insured and is in the roll of Arizona’s Registrar of Contractors. Furthermore, you can be sure that all of our technicians passed rigorous training and our battery of background checks.
If your torsion spring isn’t lifting your door or your door is stuck, it is best to not attempt fixing it on your own. Garage doors are very heavy and can be the source of great injury if not handled with care when a part is broken. At Advanced Garage Door Solutions, Inc., we are there for you to quickly fix the problem so that normal garage door function is restored. To learn more, call the Minneapolis office at 952-500-3921 or the St. Paul office at 651-769-7191 and request a free estimate.
If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.
9.4 Slide the end of the shaft into the end bearing plate. Tighten the set screws an additional 1/4 to 1/2 turns beyond the point you finger-tightened them. Add an additional 1/4 turn if you could not find the original set screw indentations in the previous step. Heavier wooden garage doors may require an additional 1/4 turn. Caution: Under-tightening the drums could cause the drum to slip and the door to cock or fall. Over-tightening the set screws could damage the shaft or drum, resulting in the same problems. This is a critical step.
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it.
Just like on a bike sprocket, your cables can sometimes become disengaged. Oftentimes, when a torsion spring breaks, the garage door cable will snap as a result. Sometimes, the cable will cause damage to a vehicle or wall, and if a person happens to be in the way of the cable it can cause serious harm. If you cables have snapped, you should call a professional to help you. See the video above. https://www.youtube.com/watch?v=Z_eZc-kh40c
If you haven’t looked at garage doors lately, prepare to be pleasantly surprised. We’ve taken the garage door and made it stylish with designs to complement both classic and contemporary homes while still keeping the functionality you desire. A garage door can represent more than 30% of your home’s curb appeal, which makes choosing the right design especially important – and Home Depot has the widest selection available. With over 1,000 different garage door designs in wood, steel, composite, aluminum and glass, you’re sure to find the perfect style to transform your garage… and your home.
Warning! If the door is partially open and crooked, don’t touch it. Period. It’s a sign your door is off balance, and it’s usually caused by a problematic cable. It’s likely the door is still under tension from the spring, and one false move could send a 150-pound door crashing down, causing damage or injury, says Vincent Johnson, owner of Garage Door Doctor of Cypress, Texas.
How much should a garage door spring replacement cost? The national average is between $200 and $300 for a professional to come to your house and replace two springs. On line sources suggest a higher price of over $700 and that you will save $500 or more by replacing springs yourself. This is simply not true. To find the cost for replacing springs in your area look for a reputable company through Yelp or the Better Busienss Bureau. If clicking a site's BBB logo doesn't take you to the BBB site, we advise purchasing your springs from a different company.

I really think that bill was way to much.I had I stalled new door springs with the help of a friend but tube door didn't. want to open .that's why I called sears so the man that came to my house spent about 15 minutes working all that be did was remove the new springs saying they were the wrong springs and put the old springs back on that's all he did .
Copyright © 2019 HubPages Inc. and respective owners. Other product and company names shown may be trademarks of their respective owners. HubPages® is a registered Service Mark of HubPages, Inc. HubPages and Hubbers (authors) may earn revenue on this page based on affiliate relationships and advertisements with partners including Amazon, Google, and others.
Luckily, there is a bit of science to questions of garage door repair and replacement. That’s why we’ve put together this guide on when to replace a garage door. We’ll prepare you to compare repair vs replacement garage door costs. We’ll discuss the ways in which repairs are the most affordable option while also exploring those moments when replacement will in the end provide you with more value added.

If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
The cost to repair a garage door is typically more affordable than installing a new garage door. Often, a garage door repair simply requires fixing a broken spring. The average cost to repair a garage door spring is $180, but prices range from $100 to $350 if the installer must disassemble the brackets to reach the springs. Common garage door repairs include lubricating or balancing the springs and installing safety cables that work as a backup for an extension spring system. Most homeowners can lubricate the springs on their own for the cost of the lubricant ($5 to $6), but many garage door contractors include lubrication services as part of their maintenance plans. Refitting existing springs to balance the door requires between 45 to 90 minutes to complete, with a price tag ranging from $75 to $110. Safety cable installation costs between $150 and $200.
Can you find what you need in the big home improvement stores? Can they show you how to fix a broken garage spring? Do they know what tools and replacement parts you need? Do they know what safety precautions you need to take? If you have any questions during the project, can you call them for help? Have they ever actually repaired a broken garage door spring themselves?

Garage Door Repair In My Area Centennial Co


Most residential garage doors have one of two types of springs: torsion or extension. Torsion springs are heavy-duty springs mounted to a metal rod that runs parallel to the door, directly above the door opening. These springs are loaded, or tensioned, with a twisting action. When the door closes, cables attached to the bottom corners of the door pull on pulleys attached to the ends of the metal rod the springs are mounted on. The pulleys turn the rod, which twists the springs and creates tension. When the door is opened, the springs unwind and help lift the door.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Does your garage door seem to be jammed? There are several reasons this could have happened. The answer may be simple and easy to fix, or there may be a larger underlying problem with your garage door system that requires an expert to repair. Run through the following list to determine if it's a problem you can fix on your own or if you should call a professional garage door technician to repair it for you.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
Often companies will show different types of springs like oil dipped, galvanized or powder coated and try to convince you that one is longer life than the other and that is why it is going to cost this much instead of that much. Galvanized and Powder coated are great for coastal areas as a rust preventative but do not change the cycle life and do not cost but a few dollars more.
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.
11.2c If the springs you installed are too weak, and you wind the springs the correct number of turns, the door will be heavy at the floor, and it will not stay open half way, but it will stay open if raised completely. If tension is added to the torsion springs to lighten the garage door and to get it stay open half way, the door will be harder to close; openers often damage the new steel garage doors when they are too hard to close.
A garage door spring replacement should cost between $175 and $225 for a single tension spring and between $250 and $300 for two tension springs. Most garage door companies carry a wide enough variety of spring sizes to cover most residential doors. As long as the proper amount of turns are put on the spring, there are more than one correct springs to use for any one door.

Garage Door Repair Installation Centennial Colorado 80016


If the door opens this way, then there’s probably something wrong with the garage door opener. It’s a good idea to make sure the opener is plugged into its nearby power outlet. Also, make sure the circuit breaker for the garage door opener hasn’t flipped to the “OFF” position. If it has, then there may be an electrical issue that your garage door specialist should check out.

I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:
Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.) https://youtube.com/e/Z_eZc-kh40c?app=desktop
Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained. http://youtube.com/watch?v=Z_eZc-kh40c

6.1 It is time now to unwind the old spring that is not broken. A few warnings are in order. NEVER, NEVER, NEVER touch a set screw without first inserting a properly fitting bar into the winding cone! Also, do not use box or socket wrenches for the set screws. If the cone slips, the wrench could break your hand in 10 spots before unwinding completely. It's my guess that this is the number one cause of trips to the emergency room for inexperienced homeowners fixing or replacing their springs.

Garage Door Repair Guy Centennial Colorado 80015


If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you.

Install new or use this right-wound torsion spring Install new or use this right-wound torsion spring to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding rod is included with ...  More + Product Details Close
Good response time and service; Question - I googled to find the Sears Garage Door repair phone number. During the conversation, I was unsure if this was "Sears" or a "contractor service" or other service. I had to ask if this repair person was coming from "Sears" or an independent repair. I was concerned until the service man arrived in a sears truck wearing Sears apparel. You might want the process to be more clearly identified as Sears.
If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own. http://www.youtube.com/embed/Z_eZc-kh40c
Thanks for asking for our input. I have enjoyed the 'Future House' episodes that you folks have created. And, I think that the amount of segments-per-season seems just about right - any more and it might begin to take the shows into an area that moves away from their core meaning (i.e. - home repair/rehab/construction, etc). Though, it's easy to understand how new and upcoming technologies fit well into TOH/ATOH's overall picture. Also, Ross Trethewey is a good sement host - very knoledgable and enthusiastic - and, as well, he gives the TOH/ATOH audience some 'younger blood' to continue forward with the show's traditions. My thoughts are to stick with 'Future House' segments.And, thanks for all of the good work you folks do in continuing to present to us each year such wonderful productions as TOH and ATOH, which we get to enjoy and benefit so greatly from!
Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

I really think that bill was way to much.I had I stalled new door springs with the help of a friend but tube door didn't. want to open .that's why I called sears so the man that came to my house spent about 15 minutes working all that be did was remove the new springs saying they were the wrong springs and put the old springs back on that's all he did .

One spring or two springs? If you have a two-car garage, it’s industry’s best practices to replace both springs, even though only one may be broken. When one spring breaks it makes sense that the other spring will most likely break shortly thereafter. Why pay for another service call? Additionally, since springs need to have the same tension, replacing only one is not effective.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills. 

Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
We are proud of the work we do in Northwestern North Carolina. We love this community and we love serving it. So whether you think you need a small repair or a major overhaul, we want to be the team that helps you increase the value of your home while making it a safer place to live for you and your family. Our professional and friendly sales team are eager to connect with you, so contact us today and find out just how we can ease your concerns and make transform your garage!
5.1 With the cables still tight on the drums, mark the drums and torsion shaft at each end with a file or a marking pen. If at least one of the springs is still wound, don't touch the cable drums and don't grab the shaft. If the cable breaks, the drum could spin and the cable rip through muscle and bone. If the set screws aren't tight enough, the shaft could spin and cause injury.

Garage Door Repair Near Me Centennial Colorado


If you notice that the garage door opens normally but doesn’t make any attempt to close when the remote is pressed, the first thing you’ll want to do is visually inspect the photo eyes. Over time, these eyes can get dirty, causing the light from the beam to be blocked. They also can eventually become misaligned, causing the eyes to not match up on both sides. https://www.youtube.com/watch?v=Z_eZc-kh40c&feature=share
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.
We offer industry leading service performed by the best licensed professionals in the region. Whether you need springs replaced, a motor repaired or need a new panel on your door, our service workers will get the job done efficiently and effectively, ensuring that your door is back in working order as soon as possible. We also offer a wonderful preventative maintenance program. This is a cost effective way to ensure that you avoid future problems by having the small, unnoticed issues addressed right away.
I told several people that I planned on installing a garage door torsion spring after mine broke. ALL of them told me that it was too dangerous and a few feared for my life! Honestly it was one of the simplest home repairs I have ever done. That is thanks in large part to your very helpful installation video. Your videos on measuring springs etc. were also very helpful. All of the necessary details are there.

Garage Door Repair And Service Centennial Co 80015


Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs.

Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician. 

The installation was amazing. Through no fault of the installer, the device arrived very late yet they were extremely accommodating. They went out of their way to keep the installation completed today. Amazon dropped the ball on the delivery but the installer made their end of the process amazing. The installer was pleasant and knowledgeable, very friendly and professional. I would hire them again. Kudos to an outstanding job. I love the convenience and the fabulous communication throughout. Far above my expectations.
The two main garage door operating mechanisms are sectional roll-ups or tilt-ups. Garage door repair services can fix single-car, double-car or RV-height doors. Your garage door may be made of wood, steel, aluminum, masonite, vinyl, fiberglass or another material. The type of garage door repair you need really depends on the type of garage door you have and the issue at hand. Garage door repair pros often charge a flat service call fee to diagnose the problem and provide an estimate. For customers who choose to have the repair done, the service call fee may be applied to the first hour of labor (including time to make the diagnosis). If your garage door is under warranty, the repair may be free of charge.
Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.
Prices, promotions, styles, and availability may vary. Our local stores do not honor online pricing. Prices and availability of products and services are subject to change without notice. Errors will be corrected where discovered, and Lowe's reserves the right to revoke any stated offer and to correct any errors, inaccuracies or omissions including after an order has been submitted.
Automatic doors require not only the installation of a heavy door, but the motor and cables as well. Automatic doors are much more common now because of their convenience, but in a case such as the heavy wood door, they are a necessity. A strong motor is required to pull up a heavy door. However, automatic doors are not without their faults -- they quickly become a manual door when the power goes out.

Garage Door Installation – This includes the installation of a new garage door. Includes the door itself, the track, cables, springs, hinges, handles, locks and rollers. It is the complete service and installation of a new door. We inspect all the parts, make adjustments to fit your garage opening, and service all elements during the installation process. Plus, we check to ensure all parts are in proper working order after installed.

Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.


If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own. http://www.youtube.com/embed/Z_eZc-kh40c
Depending on the type and location of the damage you might have an alternative to replacing panels, or entire garage doors. One solution to give new life to your garage door is repair. Small dents, rot, rust or holes can be repair without replacing. Depending on what wrong with the panel, average prices for repair are $130 for steel door repairs, $190 for wood, $170 for aluminum and $150 for fiberglass. Garage door panel repair can save homeowners money, but should be weighed against garage door panel replacement.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.

Garage Door Repair Near Me Centennial 80016


Most homeowners never know they have a broken garage door spring until they try to leave their home. You go in the garage to open the door, push the wall button, and the door only goes up 6”. The reason for this is the garage door opener force or sensitivity has activated, causing the opener to stop pulling the door up. This is a safety feature built into most garage door openers. It is actually a good thing when the open force activates to prevent any damage to your garage door or opener.


If the door closes but then immediately pops open again, you'll need to check the limit settings, which help the mechanism determine how far to move the door in order to close it properly. If the settings are off, the door will hit the ground before the opener believes it should. It will assume that it has hit an obstacle and will automatically backtrack to avoid damage. Check the owner's manual or the buttons on the motor to adjust the limit settings. It may take some trial and error to get the setting just right.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor. http://www.youtube.com/v/Z_eZc-kh40c
Chris was very professional & thorough. He arrived on time & was able to answer all questions that I had. I was extremely satisfied with the quality of the work he performed. I spoke several times on the phone with Mrs. Carol who keep me informed prior to, during, and after the installation of my garage door. She was very professional, easy to talk with and resolved any misunderstanding that I had.
Popular queries include: garage door panel replacement, garage door panel cost, garage door panel replacement cost, garage door replacement cost, garage door panel replacement cost, garage door repair, garage door replacement panels, garage door bottom panel replacement cost, garage door repair cost estimate, garage door dent repair cost, garage door panels.
I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks
×