However, if you are confident that you don’t just need new batteries, make sure to call a professional. A service person with a lot of experience will be able to look at the problem and quickly diagnose the issue, saving you precious time. Again, while you may be able to save money in the short term by taking a day off and troubleshooting the problem yourself, the amount of energy and time lost as you search out the issue will quickly surpass the cost of a professional repair.
8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page.
Garage door problems don’t have to mean the end of the world. Garage door repair is typically a one-day process and can be done for only a few hundred dollars. Common garage door repair requests include fixing slow or erratic garage doors, addressing strange sounds coming from the garage door or motor, fixing cosmetic damage such as dents or scrapes, repairing broken doors that are stuck open or closed, and troubleshooting inoperable doors.

Before we help you diagnose your stuck garage door, safety concerns can't be over stated. When trying to figure out how to fix a stuck garage door, it is important to take every safety precaution. Garage doors weigh hundreds of pounds and torsion springs hold a tremendous amount of energy waiting to be released, so without proper precaution it is possible to hurt yourself attempting to perform unauthorized repairs.
Thanks for asking for our input. I have enjoyed the 'Future House' episodes that you folks have created. And, I think that the amount of segments-per-season seems just about right - any more and it might begin to take the shows into an area that moves away from their core meaning (i.e. - home repair/rehab/construction, etc). Though, it's easy to understand how new and upcoming technologies fit well into TOH/ATOH's overall picture. Also, Ross Trethewey is a good sement host - very knoledgable and enthusiastic - and, as well, he gives the TOH/ATOH audience some 'younger blood' to continue forward with the show's traditions. My thoughts are to stick with 'Future House' segments.And, thanks for all of the good work you folks do in continuing to present to us each year such wonderful productions as TOH and ATOH, which we get to enjoy and benefit so greatly from!
A garage door with aging springs puts an enormous load on a garage door opener, so another sign of failing springs is when you hear the electric door opener begin to strain as it attempts to lift the door. At this point, it is time to consider replacing the springs. Aging door springs can also break suddenly, a situation that can cause the door to slam shut violently. If you happen to be present when a spring breaks, you will hear a very loud sound like a gunshot, because the break usually occurs when the spring is fully loaded—stretched or twisted to its full tension. When one spring breaks, the door will suddenly feel very heavy when you try to open it by hand, and an automatic garage door opener may no longer be able to lift the door at all. https://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]

We look out for the safety of our customers and their families. That’s why we do not sell garage door torsion springs separately to consumers, and it’s also why we recommend putting your broken garage door in the hands of our experienced technicians. At Garage Door Medics, we are licensed, bonded, and insured. We have completed thousands of garage door installations and spring repairs, and we make sure they are done safely and with the right springs for your garage door system.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.
9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
Surprisingly, your garage door just being locked can be causing your problem. Some garage doors have a “full lock” system which enables you, or anybody, to lock your garage door from the outside by only turning the handle. This could mean that anyone in your driveway (children, bystanders) could have turned your handle and mistakenly locked the garage door without you being aware of it. This is an easy fix by realizing this problem and then unlocking your garage door. rong.

As we’ve mentioned before, springs are installed within your garage lift mechanism in order to help lift the door. Because doors are so heavy, the lift motor would undergo far more significant wear and tear if it had to lift the full weight of the door every time you opened it. Furthermore, in order to ensure that you can open your door even if you lose power in your home, springs allow you to lift the door by hand when the motor is disengaged.


10.13 Slowly pull down on the winding bar until the garage door rises 3" and the roller hits the vise grip on the track. The door will usually drop back down and raise the bar. If it doesn't, lift the end of the bar until the door closes. If the door comes up by itself when you hold the bar lightly, the springs are either over wound or they are too strong. You may need to remove 1/4 to 1/2 turns from the springs. If the door comes up on its own, you either have to many turns on the springs or you have the wrong springs. This can be very dangerous. We recommend getting professional help. Removing the winding bar could cause the garage door to knock you off the ladder.
Garage door torsion springs are usually the first to break or give out among the many components of your garage door. This is because the springs bear a lot of pressure, supporting the entire weight of your garage door which can oftentimes be quite heavy. Through regular and continued use, garage door springs are usually stretched tight and subject to wear and tear.
Next, check to see if your garage door operator is the problem. Do this by pulling the emergency release cord when the door is in the down position (so the door doesn’t come crashing down in case there is a problem). Then, try to lift the door up manually. Does it open easily? If so, your opener is probably at fault. If it still doesn’t move, the problem likely lies with your tracks, springs, or rollers. http://m.youtube.com/embed/Z_eZc-kh40c
7.3 Slide both torsion springs out above the top of the garage door toward the cable drums. Notice that there is only one bushing or bearing between the cones. Sometimes a single bearing is pressed into the bracket; other brackets have a single bearing or bushing that fits in either cone. Do not try to install a bushing or bearing in both of the stationary cones. You will risk breaking a cone. The purpose of the bushing is to keep the shaft from wearing against the spring anchor bracket. Only one bushing is needed to accomplish this.
When you install a new garage door, replace all the hardware as well. If your automatic opener doesn’t have an automatic reversing system that includes photoelectric eyes, replace it. Doors with openers also require two extra pieces of hardware that you’ll see in Photo 4: a support strut (usually included in the door kit) and an opener bracket (not included). For doors with torsion springs located over the door, spend the $50 or so to have a garage door professional release the tension.

Automatic Garage Door Repair Centennial Colorado 80015


9.14 Slide the springs to the bracket. Double-check to make sure you have the right wound spring on the left side and the left wind spring on the right side. Turn the springs until the ends are facing you. The wire at the ends of both torsion springs here at the bracket should be pointing down. At the winding cones at the opposite ends, the spring wire points up. If not, reverse the springs. About once a month we get a phone call from a do-it-yourself customer who begins the conversation with, "I wound the garage door spring to about six turns and the spring came loose from the cone." We normally refer them back to this step and suggest they switch their springs.

Every homeowner can relate to how life's inconveniences are thrown at you at the worst possible times. The last thing you want to happen is have your car stuck in the garage when you need it most, especially when it's only been a couple months, weeks, or even days after your last garage door repair! That's why Precision leads by example and follows the industry's best practices in order to make the best recommendation to homeowners each time we step foot in a garage.

A standard double garage door is 7 ft. high by 16 ft. wide. Standard single doors are 7 ft. high by 8 or 9 ft. wide. Because the doors are so large, few home centers and only some garage door stores keep many doors in stock, so expect to order one instead of buying it off the shelf. Garage doors are available in wood, fiberglass and steel. Steel doors, like ours, are light, maintenance-free, affordable, readily available, and have an insulating value as high as R-19.
Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.

Garage Door Repair Free Estimate Near Me Centennial Colorado


If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.

Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.

The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.

Garage Door Repair Images Centennial Colorado 80015


Doors with extension springs have two sets of pulleys (which are sometimes called sheaves): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.
In most cases, only one spring breaks or wears out at a time, and you can get away with replacing just the failed spring. But this is a little like replacing old car tires one at a time. You'll get the best performance if all the springs are new and have the same strength. Extension springs are replaced individually, making it more tempting to replace just one. With torsion springs, you have to disassemble everything to replace either spring, so it makes sense to swap out both springs during the repair.
×