10.3 At this point you will wind the spring. Notice that the end of the spring on the winding cone points up when facing you. You will wind both springs up and counter intuitively as if you are trying to unscrew the winding cones from the ends of the springs. Begin by turning the spring up 1/4 turn until it meets resistance. This is your first quarter turn. Count "one." Next, insert the bar and raise it 90 degrees. Insert the second bar. This is "two." As you wind the spring it should grow in length the thickness of one coil for every turn. The cone should cover your mark after the first couple turns. Many garage door tradesmen mark the torsion springs with chalk or paint, but this often generates confusion.


The technician did a wonderful job - arrived on time and completed the job in less than 2 hours. I would have given him a 5 on everything if he had returned to add the additional piece (a piece that is fixed to the door frame for better insulation) to my door on the outside on the day he said he would come back. The piece he brought was of wrong color and he said he would be back with the right color the first day after New Year's Day to put up the piece. I hope he can come back soon.

I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks

However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!

Garage Door Repair Free Estimate Centennial Co


When a garage door service company gets a phone call in reference to a broken spring, the first thing the homeowner usually says is “the cables are broken”. This makes sense because the cables on a garage door will fly every which way, fall to the ground, become disconnected from the door, or even get caught in between the garage door and the jamb. It is rare for cables to break or need replacing when a garage door spring breaks. If your garage door has two torsion springs, the second spring will keep the cables tight and on the drums. You will have to look up at the springs to determine if one is broken.
8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page. http://www.youtube.com/watch?v=Z_eZc-kh40c
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor.

In addition to spring replacement, Aladdin Garage Doors provides expert garage door repair for your opener and garage door. Whether it’s cables, rollers, brackets, hinges, drums, gears, tracks, rails or any component that would cause your door to not operate properly, call us today to schedule an appointment or complete our online form.  Ask about our same-day service availability.


Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring. 

If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?

Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs. https://m.youtube.com/v/Z_eZc-kh40c
Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and

Garage Door Repair Installation Centennial Colorado 80015


My garage door torsion spring broke so I decided to replace it myself. Shipping was next day. I got the torsion spring rod at a local hardware store. Easy to install once I figure out how to lock down the rod from moving and loosening the door cable on the side. Instructions tells you how to do it. Great replacement spring and save $$$ doing it myself.

9.9 Go to the other side of the garage door and insert the end of the cable into the drum. Rotate the drum until the cable is tight. Slide the drum against the bearing and push the shaft to the right. The marks should line up. If they don't, figure out why and correct the problem. It could be a stuck cable, the garage floor may have shifted, or the vertical angle that helps support the bearing plate may have loosened and shifted. Many garage doors have been installed with a gap between a drum and a bearing plate. The cable drums should always be flush against the race of the bearings.
Traditional One Panel: These doors consist of one large panel which tilts to open by employing a spring mechanism to swing upward. The wood version is popular in the South and Southeastern US, where a milder climate keeps the wood from rapidly deteriorating. Traditional garage door designs include Cape, Colonial, Ranch, Tudor and Craftsman. The disadvantage is these doors require a lot of clearance to operate correctly. Sometimes repairs can be difficult because of the heaviness of the door or its inaccessibility. Average cost to repair tilt-up doors is $172.
×