With hundreds of moving parts that are all required to work together, it's no surprise that garage doors may need occasional repair and maintenance. Garage door repair services are also required in emergency situations, like when the garage door won't operate and the car is trapped inside or you've accidentally backed into the door when it was closed. Whether it's a specific repair of your garage door opener, a broken spring that needs to be replaced, or a bent or rusted track, The Home Depot's local, licensed service providers can get the job done quickly and efficiently.
While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.

We also have a wide range of expertise repairing and installing both residential and commercial doors, meaning we can tackle any problem, large or small. We carry a wide range of doors from one of the industry’s leading manufacturers, Clopay, so you can make the choice that makes the most sense for your home and family while feeling confident that you are getting a door of the highest quality. 

Garage Door Repair Companies Centennial Colorado 80016


Garage door springs can —and will—break, and if you're anywhere near the garage when this happens, you'll know it. Nothing else sounds quite like a giant metal spring snapping under tension. Even if you don't hear it, you'll know the spring broke as soon as you (or your garage door opener) try to lift the door and finds that it now weighs twice as much. So faced with a broken garage door spring, the question is, can you fix it yourself?
Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained. https://m.youtube.com/watch?v=Z_eZc-kh40c&feature=youtube_gdata
Check your garage door rollers to see if they have come off their tracks. If no damage has been done, a tech should be able to easily place them back on. If the track has become bent, however, it must be repaired and possibly (depending on the amount of damage) replaced. Don’t operate your door if it's off track or your track is bent. Your door could become seriously damaged.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door. http://www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c


Determine the inside diameter of the spring and the size of the coils. Run a tape measure across the opening at one end of the spring. Carefully measure the inside diameter of the spring so you can provide the supplier with this information. Then, use a tape measure to find the length of 10 coils on the spring. Divide the length by 10 to determine the measurement of a single coil.[7]
If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.

If the door opens this way, then there’s probably something wrong with the garage door opener. It’s a good idea to make sure the opener is plugged into its nearby power outlet. Also, make sure the circuit breaker for the garage door opener hasn’t flipped to the “OFF” position. If it has, then there may be an electrical issue that your garage door specialist should check out.

Garage Door Repair In My Area Centennial Co 80015


The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube. https://youtube.com/v/Z_eZc-kh40c?version=3
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]

Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener.
I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.
While you can certainly redo any security features on your garage door, it is often wise to replace the entire door if in fact that is the way a burglar gained access to your house. A new security code may seem like enough, but you don’t know how the thief figured out the old code in the first place. If the motor was disengaged, the issue might be a design flaw in the door itself. The best way to ensure that the thief doesn’t return or another thief doesn’t take advantage of the same unknown security weakness is to install a new door. Again, doing so with give you access to the kinds of robust security features that are being installed and implemented in the newest garage doors on the market.

DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

A1 Garage Door Repair Centennial Colorado 80016


Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
Gather the supplies and tools needed for changing the springs safely. In addition to the torsion springs you'll need a minimum of one or two 10" vise grips, an adjustable wrench, and two 1/2" X 18" winding bars. Most hardware stores sell 1/2" X 36" steel rods that can be cut in half. You'll also need a firm ladder and a rag for cleaning your hands. A ruler and a file may also be necessary; a socket wrench and sockets would shorten the time required. Finally, make sure your garage is lighted well.
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs. http://youtube.com/v/Z_eZc-kh40c?version=3
If your torsion spring isn’t lifting your door or your door is stuck, it is best to not attempt fixing it on your own. Garage doors are very heavy and can be the source of great injury if not handled with care when a part is broken. At Advanced Garage Door Solutions, Inc., we are there for you to quickly fix the problem so that normal garage door function is restored. To learn more, call the Minneapolis office at 952-500-3921 or the St. Paul office at 651-769-7191 and request a free estimate.
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and
The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube. https://youtube.com/v/Z_eZc-kh40c?version=3
Popular queries include: garage door panel replacement, garage door panel cost, garage door panel replacement cost, garage door replacement cost, garage door panel replacement cost, garage door repair, garage door replacement panels, garage door bottom panel replacement cost, garage door repair cost estimate, garage door dent repair cost, garage door panels.
Garage door problems don’t have to mean the end of the world. Garage door repair is typically a one-day process and can be done for only a few hundred dollars. Common garage door repair requests include fixing slow or erratic garage doors, addressing strange sounds coming from the garage door or motor, fixing cosmetic damage such as dents or scrapes, repairing broken doors that are stuck open or closed, and troubleshooting inoperable doors.

To realign the track, first loosen the screws that hold the track to the frame. Then, gently tap the track with a rubber mallet to move it back into the proper position. Use a level to ensure it’s perfectly straight. Once you have the alignment correct, tighten the screws securely to ensure the track won’t move and cause more issues when opening your garage door. You’ll need to repeat this same process on the other tracks as well, as these may also be out of alignment.
Call us today for new garage door installations, repairs or replacement. Most times a small adjustment is all that’s needed to make your garage door last for years to come.  We fix broken springs, replace rollers, anchors, brackets. Replace bent panels, re-align sensors, replace perimeter seal or bottom seal and much more. We also offer a safety inspection & tune-up services to keep your garage door opener running smoothly.
There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
10.7 Continue tapping until the cone moves out to the mark on the shaft. Continue holding the bar off the garage door and pulling back toward the center of the door. If the cone slips away from the mark, repeat this step. Keep an eye on the tape to make sure the bar doesn't slip out of the cone. If it does start to slip, rest the bar against the top of the garage door, insert a bar in the next hole and turn the cone up enough to make it possible for you to push the marked bar back into place.
A1 Garage Door Service is the trusted service provider in installing, servicing and repairing all kinds and types of garage doors. We encourage you to check out the reviews of the people of Albuquerqueon the kind of garage door service that we provide. Our customers have consistently given us A+ ratings on BBB, 5-star ratings on Yelp and the Super Service Award on Angie’s List to express their satisfaction on our service.
If you have a garage door opener and you suspect a spring has broken, do not disconnect the opener from the door (by pulling the red emergency release handle) while the door is open. If you do, the door can come crashing down under its nearly full weight, with nothing to stop it. This is an extremely dangerous situation. It is never safe to leave the door open when a spring has broken because someone might try to close the door without realizing how heavy it is. Or, they might pull the emergency release handle on the opener.
Since 1998, our clients have always been our top priority. That is why we strive to ensure efficiency and reliability in all our services. This is evidenced by our consistent Yelp 5 Star rating, A+ rating from BBB and Super Service Award from Angie’s List. You can trust that our work is done with quality as we are licensed, bonded and insured and is in the roll of Arizona’s Registrar of Contractors. Furthermore, you can be sure that all of our technicians passed rigorous training and our battery of background checks.

Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.
×