No matter what kind of door you are installing, be very careful. The instructions that follow are merely guidelines. You should read your garage door manufacturer's instructions and owner's manual very carefully before attempting either type of installation. And if you're a do-it-yourself greenhorn, skip this project and hire an experienced professional. It may be more expensive, but garage door installation is on the higher scale of DIY difficulty.

There’s nothing more frustrating than attempting to open or close your garage door only to find that it simply won’t budge. In some cases, your garage door may even open or close halfway only to get stuck in the process. The very first thing that you should do if your garage door seems to be stuck is to check the batteries in your remote. You’d be surprised at how often this is the root of the trouble. If dead batteries were not the issue, then use the following four tips to further troubleshoot your garage door. https://www.youtube.com/watch?v=Z_eZc-kh40c&app=m

If your garage door isn’t operating properly, the torsion springs are likely to blame. If you’re concerned about tackling this project on your own, consider hiring out the job to a professional. Otherwise, replace both the left and right springs at the same time to save yourself from having to do the job twice. Remove the old springs and measure them while they’re relaxed. Only then will you be able to order replacement parts and install the new springs. Replacing your own garage door springs takes only a little time and effort and can save you hundreds of dollars.
Texas Garage Door and Opener in Plano, TX provides residential garage door and commercial overhead door services throughout Dallas, Fort Worth and the surrounding areas. Our fully insured team specializes in garage door installations, repairs and maintenance services. We have over 25 years of combined experience and qualified technicians ready to service your garage door needs. We are available 24/7 for emergency service, please call 972-633-3872 today! http://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
I had two extension springs replaced, all for $135.00 (this included tax). The work took about 35 minutes and I was relieved to have this taken care of. You never realize the importance of something to you, until it is broken. Was this a good price? Seemed reasonable enough and the repairman came out the same day I called. Harris County Houston, Tx.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.

Garage Door Repair Free Quote Centennial Co


A garage door with aging springs puts an enormous load on a garage door opener, so another sign of failing springs is when you hear the electric door opener begin to strain as it attempts to lift the door. At this point, it is time to consider replacing the springs. Aging door springs can also break suddenly, a situation that can cause the door to slam shut violently. If you happen to be present when a spring breaks, you will hear a very loud sound like a gunshot, because the break usually occurs when the spring is fully loaded—stretched or twisted to its full tension. When one spring breaks, the door will suddenly feel very heavy when you try to open it by hand, and an automatic garage door opener may no longer be able to lift the door at all. https://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
When your garage door is stuck after a power outage, your whole day can suffer. Summer storms hit, your garage door opener gets caught in the crossfire, and before you know it, your car is being held hostage by your garage. While it stinks to have your garage door stuck open because of safety issues, it may be even more frustrating to have your cars trapped inside. Just like saying your dog was eating your homework as a kid, now you have to explain to your boss how your car is being held hostage. Good luck.

A1 Garage Door Repair Centennial Co 80015


If your garage door's spring breaks, stops working properly, or snaps, you'll lose the ability to open and close your garage door. This could happen due to a variety of issues, like normal wear and tear or from extreme temperature changes in a short amount of time. Spring replacements require a quick response from a garage door provider near you. Contact The Home Depot and a local, background-checked technician will respond within 24 hours.

Garage Door Repair Emergency Centennial Colorado


Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.

Automatic Garage Door Repair Centennial Co 80015


10.2 Tape your winding bars if you have not done so already, not only to assure that you are inserting the bars completely into the cones as you wind the torsion springs, but more importantly to assure that the bar does not slip out of the cone when you stretch the springs at the end. This has happened to me several times. Professionals always stretch torsion springs after winding them because the shaft floats horizontally between the flexible end bearing plates as the door operates. Although this may be as little as 1/4", the binding of the coils as the garage door closes oftentimes keeps the door from closing completely, especially when the torsion springs and bearings are dry.

DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

A1 Garage Door Repair Centennial Colorado 80016


Because your garage door can be customized, pricing varies. Our Clopay configurator will help you review pricing as you begin your project. You’ll start with your door size and whether you need a single or double car door. Next, you can choose the collection of door, which gives you options of various materials and styles. Then, you’ll choose your construction, which allows you to decide what you need in terms of energy efficiency, durability and noise control. Lastly, you will be able to visualize the design and see an end price. Other optional add-ons include windows, decorative hardware, smart features and the r-value. However, you do not have to use the configurator. We also install standard garage doors that have not been customized so you know the product price early on in the process.
7.2 If the spring bracket is slotted, vise grip the bracket to secure the shaft in the bracket. This will keep the shaft from possibly falling out and causing injury or damaging the garage door or shaft. You can also secure the shaft with a cable tie. Remove the bushing from the cone and leave it on the shaft next to the center spring bracket. Often the bushing gets stuck in the cone and customers will call us about getting a new bushing until they discover it is still in the cone of the spring replaced earlier.
Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them. http://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door. http://www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.

Garage Door Repair Installation Centennial 80016


Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

Garage Door Repair Emergency Centennial Colorado 80016


Your decision on whether to try and replace a broken spring may depend on what type of springs you have. Garage door springs come in two main types: extension and torsion. Identifying which type you have is easy. If your door system has a long, skinny spring running parallel to each horizontal door track, then you have extension springs. If your door has one or more beefy springs on a metal rod parallel to, and directly above, the door opening, then you have torsion springs. Both of these springs are found on standard sectional garage doors. If you happen to have an old one-piece, swing-up door with vertical springs at both sides, you also have a variety of extension springs, sometimes called side springs.

10.6 Here you will need to do three things at once. With your left hand, lift the bar just off the top of the door and pull it toward the center of the garage door. While lifting up and back, tap the top of the bar just under the winding cone with your other bar. Pulling the bar back toward the center of the door as you tap causes the spring cone to bind on the shaft and not slip back.

Automatic Garage Door Repair Centennial 80016


We have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous train-ing process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
At Custom Door and Gate, we’ve been installing and repairing garage doors since 1989. We know the ins-and-outs of residential garage door repair, and we can help you diagnose your garage door issues if you’re uncertain what the problem is. We handle everything from automatic garage door repair to garage door replacement. We provide repairs and service to customers in the North Carolina area. Call us today to answer your garage door questions or to schedule a repair with our skilled garage door technicians.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
When I called to schedule the repair service, I was transferrd 5 times and spoke with 6 service reps. Each rep was very confused by my request to get my garage door repaired. One rep actually told me that Sears doesn't repair garage doors. I had to tell her that Sears installed the door. When I finally found a rep who could schedule my service, it took one week for the appointment.

We want to hear from you and encourage a lively discussion among our users. Please help us keep our site clean and safe by following our posting guidelines, and avoid disclosing personal or sensitive information such as bank account or phone numbers. Any comments posted under NerdWallet's official account are not reviewed or endorsed by representatives of financial institutions affiliated with the reviewed products, unless explicitly stated otherwise. https://www.youtube.com/watch?feature=youtube_gdata&v=Z_eZc-kh40c
The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.

Garage Door Repair Centennial Colorado 80015


If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door.
Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.

Garage Door Repair Cost Centennial Co 80016


5.1 With the cables still tight on the drums, mark the drums and torsion shaft at each end with a file or a marking pen. If at least one of the springs is still wound, don't touch the cable drums and don't grab the shaft. If the cable breaks, the drum could spin and the cable rip through muscle and bone. If the set screws aren't tight enough, the shaft could spin and cause injury.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.

Since 1998, our clients have always been our top priority. That is why we strive to ensure efficiency and reliability in all our services. This is evidenced by our consistent Yelp 5 Star rating, A+ rating from BBB and Super Service Award from Angie’s List. You can trust that our work is done with quality as we are licensed, bonded and insured and is in the roll of Arizona’s Registrar of Contractors. Furthermore, you can be sure that all of our technicians passed rigorous training and our battery of background checks.


The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.

Garage Door Repair Near Me Centennial 80016


There are several retailers that sell garage door springs and their parts. Local hardware stores often carry a selection of lubricants, torsion conversion kits, safety cables, ball bearings and extension springs. Another option is a garage door supply company or an online retailer that will usually offer a more extensive inventory. These retailers sell everything from lubricant to torsion-spring conversion kits and garage door tools. They also tend to offer information to their customers and help them locate the parts they need and understand how to complete a specific repair. http://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop

If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot. http://youtube.com/v/Z_eZc-kh40c

There are many steps to replacing torsion springs, but overall it's a simple, straightforward process. If you're inclined to attempt it, find a good online video tutorial (preferably done by a garage door pro) that walks you through the entire process, including how to buy the right size of springs. You can also buy new springs and any related parts online, along with the most important items that you need: the two solid-metal winding rods that you use to wind and unwind the torsion springs.

My garage door has been acting up. Not wanting to work sometimes. I noticed the blue light flashing on the opener when I push the remote button. Today it will not open. That is the only way in, so I can't go in the garage from inside the house. I can't pull the cord to release the belt drive. How do I open it now? I never did run wires to the manual button into the house. I have to use the opener. Only have one I can find now. It is not working. I need in there now.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
10.8 After the cone reaches the mark, continue pulling the bar off the garage door and back toward the middle of the door with your left hand. Tighten both set screws 1/2 to 3/4 turns each after each screw first meets the shaft. This is the point at which you will feel the screw meeting resistance. If the garage door spring snakes after tightening the set screws, repeat the process and stretch the spring half as much as before. Residential torsion springs are stretched 1/8" to 1/4". Larger commercial and industrial overhead garage door torsion springs are stretched as much as an inch. http://www.youtube.com/v/Z_eZc-kh40c&feature=kp
The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs. https://www.youtube.com/v/Z_eZc-kh40c?version=3
Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
×