I am a relatively new homeowner and one of the first items that needed to be replaced was my garage door. I had the 1950s style with 2 separate doors and a support column down the middle . I bid out the work and OGD came in the lowest by far and provided a much higher quality door. I converted my door to a single door. Their team installed the support beam to brace the house and support the structure and installed the new door in a day. I had my first issue with door this week, by operator error. They came out same day and repaired the door and installed a keypad for me. I couldn’t be happier with the quality of the product and the customer service provided. https://m.youtube.com/embed/Z_eZc-kh40c
If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot. http://youtube.com/v/Z_eZc-kh40c
If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced.
Garage door torsion springs are usually the first to break or give out among the many components of your garage door. This is because the springs bear a lot of pressure, supporting the entire weight of your garage door which can oftentimes be quite heavy. Through regular and continued use, garage door springs are usually stretched tight and subject to wear and tear.
We arrived at a rental property and tried to open garage door to get our vehicle in so we could unload luggage, etc. Could not open from outside. Went into house and, from inside garage, tried automatic opener but this did not work. So in trying to open the door manually, I reached up and pulled on the red cord attached to a lever. What I could not see, and was not expecting, is that the rope was frayed through almost completely. The rope broke when I applied some weight to it, sending me backwards onto the floor of the garage.
I've been watching TOH since 1981. I just happened to stumble across it on PBS during a repeat of the second season, was instantly taken with it - and, hooked-for-good. That particular show/season (the Newton/ H. H. Richardson House - 1981) remains my favorite. Also, I happened to meet Norm quite a few years back and he mentioned it as being his favorite, as well - all-the-more reason for me to have fond memories of it. If I were to pick more 'favorites' from the 'Bob-era', 'Steve-era' and 'Kevin-era' they would be: 'Bob-era' - the Lexington Bed & Breakfast (1988) and the In-and-Around Boston shows (1984); 'Steve-era' - the Concord Barn (Wickwire House - 1989), the Wayland House (Kirkside - 1991)) and the Jamaica Plain House (1990); 'Kevin-era' - the Cambridge House (2005), the Newton Shingle-style House (2007) and the Detroit Houses (2017).p.s. - I've very much enjoyed the times that the show has gone back and looked at previous projects. It's always nice to see how the home - and homeowners - have done over time. Thank you!
Install new or use this pair of left Install new or use this pair of left and right-wound torsion springs to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding ...  More + Product Details Close
When a garage door service company gets a phone call in reference to a broken spring, the first thing the homeowner usually says is “the cables are broken”. This makes sense because the cables on a garage door will fly every which way, fall to the ground, become disconnected from the door, or even get caught in between the garage door and the jamb. It is rare for cables to break or need replacing when a garage door spring breaks. If your garage door has two torsion springs, the second spring will keep the cables tight and on the drums. You will have to look up at the springs to determine if one is broken.
Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
Just like car tires are rated by miles, garage door springs are rated by an estimated number of cycles (1 cycle = your garage door going up AND down 1 time). The springs used by our competition range anywhere from 5,000-10,000 cycles, whereas we use a high-grade steel spring rated for 25,000-50,000 cycles! This is why we can put, in most cases, a Lifetime Guarantee on our springs for as long as you live in your home! http://www.youtube.com/v/Z_eZc-kh40c?version=3
If you have a steel door, but want the look of a wood one, it is not necessary to change your entire garage door. Often, it may be possible to mimic the look of wood with skillful painting. Your local home improvement store may be able to provide good advice about the type of paint and brushes needed to mimic the look of wood for your particular door material.

Garage Door Repair How Much Centennial Colorado 80016


The average lifespan of torsion springs is determined by its cycle count. Garage Door Medics provides springs with an average of 25,000 cycles and we can provide custom size springs for any door. The industry standard is 10,000 cycles. When a garage door is used more frequently, the springs may not last as long. If you begin to see signs of wear, it’s time to give Garage Door Medics a call!

DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone. http://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
We have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.

It is precisely on those coldest days of the year when you most need and appreciate the convenience of opening and closing your garage door quickly. Sadly, that's exactly the kind of day when moisture and cold can conspire to make this difficult. Garage doors can and do freeze to the garage floor. Sometimes it is just a minor icy connection between the two that can be broken when you hit the opener button. If the door refuses to budge on the first attempt, though, resist the urge to keep banging on the automatic opener button. This is likely to cause a more serious problem with the garage door opener—including, but not limited to, stripped gears, broken springs, and a burned-out motor on the opener. https://m.youtube.com/watch?v=Z_eZc-kh40c
If you need to leave the door open until you can make repairs, block the door track on both sides so the door can't move, and unplug the garage door opener (if you have one). If you want to close the door, you can try closing it with the opener, making sure there's nothing in the door's path in case something goes wrong. However, this will put some strain on the opener. Alternatively, you can have a few strong helpers hold the door while you disconnect it from the opener and carefully close the door manually—again, it will be very heavy. https://www.youtube.com/watch?v=Z_eZc-kh40c&hc_location=ufi
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
Garage doors have tension springs and cables that help to slowly and safely lower your door while closing. If these tension springs or cables break, you might find that your garage door closes really fast, often with a loud bang when it hits the ground. This is very dangerous as there is nothing preventing the garage door from crushing something that might be below it. It’s best to call a garage door professional as soon as you can to have them come out and repair these cables or springs.

Hiring a professional to handle garage door spring repair and replacement tends to be a much easier and safer option for homeowners. Removing or repairing garage springs can be a dangerous job, but professionals have the experience and equipment to do it safely and efficiently. Unless your springs only need a minor repair, such as lubrication or fixing a minor balance issue, be sure to call in a local garage door pro to do the job.


Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.

A1 Garage Door Repair Centennial Colorado 80015


Garage door springs can —and will—break, and if you're anywhere near the garage when this happens, you'll know it. Nothing else sounds quite like a giant metal spring snapping under tension. Even if you don't hear it, you'll know the spring broke as soon as you (or your garage door opener) try to lift the door and finds that it now weighs twice as much. So faced with a broken garage door spring, the question is, can you fix it yourself?
10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
There could be a few issues that might be causing your transmitters not to work properly. The most common reason could be that you’re simply out of range of your garage door. Each garage door and transmitter combo has a specific range it will function in. If you’re trying to open your garage door before you can even see your house, then chances are you’re just too far away. Try waiting until you turn into your driveway to hit your transmitter button, and you should have more success opening your garage door on the first try.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
×