If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.

Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them. http://youtube.com/watch?v=Z_eZc-kh40c&app=desktop
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open. 

A1 Garage Door Repair Centennial Colorado 80016


Depending on the type and location of the damage you might have an alternative to replacing panels, or entire garage doors. One solution to give new life to your garage door is repair. Small dents, rot, rust or holes can be repair without replacing. Depending on what wrong with the panel, average prices for repair are $130 for steel door repairs, $190 for wood, $170 for aluminum and $150 for fiberglass. Garage door panel repair can save homeowners money, but should be weighed against garage door panel replacement.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.

Garage Door Repair And Service Centennial 80016


10.4 Raise the second bar 90 degrees and insert the first bar. This is "three." Continue winding. If the spring shortens in length, unwind the spring and switch sides - the springs are on backward. Otherwise, continue winding until you reach a count of "30." This is 7 1/2 turns, which is normal for most 7' doors. Longer life springs are wound the same number of turns. Newer steel doors with only one strut on top often need only 7 1/4 turns. On 8' doors count to 34. Each time you insert a bar into the winding cone, listen for the click to let you know the bar is in all the way. Not inserting the bar all the way could cause the cone to explode.
The U.S. Consumer Product Safety Commission says that about 30,000 injuries linked to garage doors are now reported every year in the United States. Many of these injuries have involved bruised or broken extremities. However, some have included serious shoulder, back, and head injuries leading to permanent disability or even death. What is the cause of these garage door injuries? One leading cause has been homeowners trying to repair or replace their own garage door springs.
There are several retailers that sell garage door springs and their parts. Local hardware stores often carry a selection of lubricants, torsion conversion kits, safety cables, ball bearings and extension springs. Another option is a garage door supply company or an online retailer that will usually offer a more extensive inventory. These retailers sell everything from lubricant to torsion-spring conversion kits and garage door tools. They also tend to offer information to their customers and help them locate the parts they need and understand how to complete a specific repair. http://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop
The winding and unwinding is done at a metal fitting, called a winding cone, attached to the outside end of the spring. You stick a winding bar into one of the four holes in the cone and use the bar as a lever to turn the cone. Once you've completed a quarter turn, insert the other bar into a different hole in the cone and let the bar lever against the closed garage door to hold the spring tension. This allows you to move the original bar to repeat the process, alternating the bars with each quarter-turn. It takes about 30 quarter-turns to fully tension a standard torsion spring.
My garage door has been acting up. Not wanting to work sometimes. I noticed the blue light flashing on the opener when I push the remote button. Today it will not open. That is the only way in, so I can't go in the garage from inside the house. I can't pull the cord to release the belt drive. How do I open it now? I never did run wires to the manual button into the house. I have to use the opener. Only have one I can find now. It is not working. I need in there now.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.

The Torquemaster system has a lock built into each side on a double car door that will activate when a spring breaks causing the door to lock in the up position. It is very simple to deactivate this lock and get your door closed. But, you can guarantee you have a broken spring inside the Torquemaster tube on the side where the lock activated. You will need the spring inside replaced or have it converted over to a standard torsion spring set up, which is what we recommend and a service we perform quite frequently. A standard torsion spring will last 3 times longer than the small spring inside the Torquemaster tube. https://youtube.com/v/Z_eZc-kh40c?version=3

Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.


Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs! https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c

Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.

Garage Door Repair Average Cost Centennial Co 80016


If this is the problem then you will be able to tell by seeing if your garage door rollers are literally off track. If your garage door panels are not damaged, then you do not need to replace your door. However, the rollers do need to be put back on the track which should be done by a professional. If you are looking for a garage door company that specializes in Garage Doors, Garage Door Repair, or Garage Door Openers, or are just looking for more information, please visit our website at precisiondoor.net. Remember, "We Fix Garage Doors Right"™. https://www.youtube.com/v/Z_eZc-kh40c&feature=kp
Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space. 

A1 Garage Door Repair Centennial Colorado 80015


You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs! https://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.
I've been watching TOH since 1981. I just happened to stumble across it on PBS during a repeat of the second season, was instantly taken with it - and, hooked-for-good. That particular show/season (the Newton/ H. H. Richardson House - 1981) remains my favorite. Also, I happened to meet Norm quite a few years back and he mentioned it as being his favorite, as well - all-the-more reason for me to have fond memories of it. If I were to pick more 'favorites' from the 'Bob-era', 'Steve-era' and 'Kevin-era' they would be: 'Bob-era' - the Lexington Bed & Breakfast (1988) and the In-and-Around Boston shows (1984); 'Steve-era' - the Concord Barn (Wickwire House - 1989), the Wayland House (Kirkside - 1991)) and the Jamaica Plain House (1990); 'Kevin-era' - the Cambridge House (2005), the Newton Shingle-style House (2007) and the Detroit Houses (2017).p.s. - I've very much enjoyed the times that the show has gone back and looked at previous projects. It's always nice to see how the home - and homeowners - have done over time. Thank you!
Interested in garage door installation? You don’t have to know how to install a garage door or how to install a garage door opener. Lowe’s has you covered with professional, independent garage door installers to manage the job from taking measurements to the final garage door opener installation. Why take the time to learn how to install garage doors or how to install garage door openers? Invest less time and manage garage door installation costs. Contact Lowe’s for your project services today.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.
Aging garage door springs cause the door to effectively "weigh" more as the steel loses its resiliency. With new springs, a heavy garage door should take no more than about 10 pounds of force to lift into an open position. With springs nearing the end of their lifespan, the force required to lift the door can be considerably more, since a garage door may weigh 200 pounds or more.
On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.
	10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.

Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener. https://youtube.com/e/Z_eZc-kh40c
I got these replacement cables for my beach house garage door after the originals rusted and broke. These are twice the diameter of the OEM cables, and fit the door perfectly. The larger cables give piece of mind for both supporting the door and providing safety cables for the extension springs. Came with all the necessary hardware, and the installation was easy with the doors blocked in the up position.

One of the large springs on our garage door broke the day before Thanksgiving, trapping our van inside the garage. We have a daughter in a wheelchair and had lots of errands to run before Thanksgiving, so we really needed our van. We called Overhead Garage Door and they told us approximately when they would arrive. They not only replaced the broken spring, they replaced the other spring, all of the rollers and most of the hinges. They also replaced several rollers and hinges on the second garage door. The technician, Micah, and his brother could not have been nicer. The garage doors have never worked as well or been this quiet. I highly recommend Overhead Garage Door to anyone in need of new garage doors, or repairs to existing doors. A first class business.


Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]


On our EZ-Set Torsion Springs page you will find several options for replacing these springs. We also have step by step instructions for EZ-Set Torsion Spring Replacement. In addition, one of our customers has provided excellent EZ-Set Torsion System instructions for removing the spring without wrecking the winding unit that secures the stationary cone. Instead of a spanner tool, you may prefer to use a pipe wrench or large channel locks to hook the end of the spring and remove it from the cones in the last step.

10.5 If the spring comes loose from the cone at about 6 turns, you are probably winding the spring backward because the springs are on the wrong sides. Switch the springs. Otherwise, after winding the torsion springs, you will need to stretch the springs and secure the winding cone. First, mark the shaft 1/4" beyond the winding cone with tape or with a file. We stretch the springs because the shaft floats horizontally between the flexible end bearing plates as the garage door operates. Although this may be as little as 1/4" the binding of the coils as the door closes often keeps the door from closing completely, especially when the springs and bearings are dry and need lubrication.
There are several retailers that sell garage door springs and their parts. Local hardware stores often carry a selection of lubricants, torsion conversion kits, safety cables, ball bearings and extension springs. Another option is a garage door supply company or an online retailer that will usually offer a more extensive inventory. These retailers sell everything from lubricant to torsion-spring conversion kits and garage door tools. They also tend to offer information to their customers and help them locate the parts they need and understand how to complete a specific repair.
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

Garage Door Repair Installation Centennial Co 80015


Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

Garage Door Repair Free Quote Centennial Colorado 80016


"I called Garage Door Medics Sunday night to request roller replacement on my parents' garage door. I was surprised to have someone call me ...back within the hour. Jeff was able to schedule the repair for 10 am the next day. I was very happy with the prompt scheduling. Jeff arrived on time and was very compassionate and professional. He gave my elderly parents a discount on the repair, and also lubricated the door and tightened the track, as well as adjusted the sensors. Rather than replacing just the single broken roller, he advised replacing all rollers since they would most likely break around the same time. So we did. He also showed us some things to watch out for like the bowing of the spring and advised that we have the spring positioned higher when it is replaced as it is creating more tension than necessary in its current position. I was very impressed with Jeff since he didn't try to sell us a spring replacement at this time since it could last a bit longer. He understood that my retired parents had limited income. I've had other vendors try to sell me everything they could. Thanks, Jeff! "
9.8 Twist the garage door shaft to tighten the cable on the drum. While twisting, vise grip the shaft as shown to keep the cable tight on the drum. The top of the vise grip should be tight against the garage header. This will keep the cable snug on the first drum while you install the cable on the other drum and position it in place. It also keeps the shaft from turning and the cables peeling off when you wind the springs. That one grip can save many hours of walking back and forth and having to level and re-level the garage door after winding the torsion springs. http://youtube.com/v/Z_eZc-kh40c?version=3
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:
2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone. http://www.youtube.com/watch?feature=youtube.be&v=Z_eZc-kh40c
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

Garage Door Repair Installation Centennial Co 80015


Clearly there is a lot going on with your garage door and it takes trained and qualified experts to properly install, maintain, repair, and replace them. The experts and On Track Garage Door Services have the tools, skills, training to get your garage door fixed the first time. In addition we can help you fix your garage door affordably and offer many options from your basic garage door to custom wood styles. To find out how much your garage door repair will cost in Phoenix, Scottsdale, Mesa, Chandler or anywhere else, give us a call at 480-641-2301 or use our Contact Page.


Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.
If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.
×