If you are not sure if your door had the correct springs, we recommend that you weigh your door using an analog scale. From my own field experience I would estimate that at least 10% of the doors have the incorrect springs on them. In addition to this, most manufacturers spring their doors using a 20 pound window. We like to improve the garage door balance.

Garage Door Repair Centennial Colorado 80016


While it would be wonderful if door springs lasted forever, the reality is that the simple act of opening and shutting the door multiple times every day isn’t easy. It’s hard on the springs, even though they’re built to do it. Most springs will last for a while, but they won’t last forever. The regular wear and tear of endlessly opening and shutting the door breaks them down and eventually, they’ll need to be replaced.
Rolling sectional overhead garage door spring replacement should cost somewhere between $195 to $300 for a quality set springs (50000 cycle rating). This price will very if the garage door repair company charges a service call fee (trip charge). The most important thing to consider along with price is the quality of the springs and the warranty. There are any company that we use lower or mid quality springs and charge on the higher end because they include a lifetime warranty on the springs. The catch is that this warranty will only covers the spring for life and labor only for 30 days to a year. Look for a company that offers a equal parts and labor warranty. This insures that the warranty represents the rating of the springs that are being installed. For instants, you may buy a 1500 cycle rated spring set (last 3 years +or-) for $200 with a lifetime warranty and 1 year on labor. When a spring brakes after 3 year the spring its self is covered but the labor cost to replace the warranty spring can be between $65 to $100. This can add up over the year as the warranty will not restart at the time of the warranty replacement. On the offer hand, if you purchase a set of springs rated at 50000 cycles (last 10 year +or-) for $270 with a 10 year parts and labor warranty and a spring brakes in 8 years it would be replace at $0 cost. A must batter value! Always check service company review and get the details on the quality of springs a garage door repair company uses and the warranty, part and "labor".

Most home centers don't carry all the replacement parts you'll need for garage door spring replacement, and most garage door service companies won't sell you springs. So you may have to order the parts online and wait for the shipment to arrive. Garagedoorpartsusa.com and stardoorparts.com are two online sources . First, inspect the condition of your cables and brackets. If you see any frayed strands on the cables or rust on the bottom brackets, replace them now before they fail. Bottom brackets cost about $15 per set. Premium-quality cables (listed as “7x19”) last much longer than economy cables and cost only about $4 more. So it's smart to buy the better cables for about $12 per set.

Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]


Both types of springs are loaded, or under tension, when the door is closed. This gives them stored energy to help lift the door as it's being opened. When the door is all the way up, the springs are relaxed, or relatively so—they still may be under some tension. The mechanical difference between extension and torsion springs is that extension springs are loaded by stretching, or elongating, while torsion springs are loaded by twisting, creating torque.
Your decision on whether to try and replace a broken spring may depend on what type of springs you have. Garage door springs come in two main types: extension and torsion. Identifying which type you have is easy. If your door system has a long, skinny spring running parallel to each horizontal door track, then you have extension springs. If your door has one or more beefy springs on a metal rod parallel to, and directly above, the door opening, then you have torsion springs. Both of these springs are found on standard sectional garage doors. If you happen to have an old one-piece, swing-up door with vertical springs at both sides, you also have a variety of extension springs, sometimes called side springs.

Doors with extension springs have two sets of pulleys (which are sometimes called sheaves): one at the end of each spring and one at the top of the vertical door track. They also have two cables on each side. One cable attaches to the bottom of the door, runs up and over the pulley above the door and around the spring pulley and then attaches to the door track bracket. The other cables are safety cables that run through the middle of the springs and are fixed to a track bracket at both ends. These cables restrain the springs if they break under tension. All extension springs must have safety cables.
Next, check to see if your garage door operator is the problem. Do this by pulling the emergency release cord when the door is in the down position (so the door doesn’t come crashing down in case there is a problem). Then, try to lift the door up manually. Does it open easily? If so, your opener is probably at fault. If it still doesn’t move, the problem likely lies with your tracks, springs, or rollers.

Measure the various areas where the door will be installed: door-opening height and width, headroom (from top of opening to ceiling), and back room (length of garage). For the headroom, you should have about 10" to 12" of space, depending on the spring system you're installing. For the back room, you should have the door height, plus another 18" or more of space.
I've been watching TOH since 1981. I just happened to stumble across it on PBS during a repeat of the second season, was instantly taken with it - and, hooked-for-good. That particular show/season (the Newton/ H. H. Richardson House - 1981) remains my favorite. Also, I happened to meet Norm quite a few years back and he mentioned it as being his favorite, as well - all-the-more reason for me to have fond memories of it. If I were to pick more 'favorites' from the 'Bob-era', 'Steve-era' and 'Kevin-era' they would be: 'Bob-era' - the Lexington Bed & Breakfast (1988) and the In-and-Around Boston shows (1984); 'Steve-era' - the Concord Barn (Wickwire House - 1989), the Wayland House (Kirkside - 1991)) and the Jamaica Plain House (1990); 'Kevin-era' - the Cambridge House (2005), the Newton Shingle-style House (2007) and the Detroit Houses (2017).p.s. - I've very much enjoyed the times that the show has gone back and looked at previous projects. It's always nice to see how the home - and homeowners - have done over time. Thank you! https://www.youtube.com/watch?v=Z_eZc-kh40c&app=desktop

At DIY Garage Door Parts, we help you identify the problem and the solution. We help you find and order the right parts and tools (torsion springs, winding bars, extension springs, rollers, garage door parts, opener/operator parts, and accessories). We ship the parts on the same day or next business day. And we guide you through the process on how to repair your broken garage door springs with video tutorials and phone support. Whether you are learn how to repair a broken garage spring, and wanting to change your worn out rollers to make your door super quiet, our video library has everything you need to show you whatever garage door fix you may need. You can bring your laptop or mobile device right to your garage and learn how to fix your broken garage door springs – correctly and safely – while you watch a how to video!


Even though most of us are likely used to seeing this small spring in place on our garage door, we don’t often think too much about it, and we simply count on it working when we need it to. Unfortunately, it doesn’t last forever and will eventually need to be replaced. It’s best to be proactive and notice when it begins to look worn down before it actually breaks. Otherwise, you may find yourself trying to open the garage door to drive to work one morning, only to find that the door won’t open because the spring is broken.

Garage Door Repair Installation Centennial 80016


Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
R-value describes the power of the insulation in your door. The higher the r-value, the stronger the insulation. Those doors will have better energy efficiency than doors that have a low r-value. Basic doors have an r-value of 0.0 with no insulation. The first step up gives you 1-3/8” insulation at a 6.5 rating. Next, a 1-3/8” thickness with Intellicore has a 12.9 r-value. The best option on the market is the 18.4 r-value, which has 2” Intellicore insulation.

Garage Door Repair Guy Centennial Colorado 80016


We have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
One spring or two springs? If you have a two-car garage, it’s industry’s best practices to replace both springs, even though only one may be broken. When one spring breaks it makes sense that the other spring will most likely break shortly thereafter. Why pay for another service call? Additionally, since springs need to have the same tension, replacing only one is not effective.
I have 2 full house humidifiers that have stopped functioning right. There are new filters, fan runs, tanks are full of water but they are not empting into the base. They have worked for part of the winter and now nothing seems to help...I loosened the caps thinking I had them too tight..... nothing seems to work .I have had humidifiers for 20 years and this is the first time this has happened to me. The humidifiers are only 2 years old. Any suggestions??
×