As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!
To install a single new garage door it should cost between $500 and $800. They demonstrate that the average homeowner can usually tackle such a project in a nine hour time span and a professional will be able to complete it in roughly five hours. Should it be a DIY project? Not really, most housing experts point out that it is a two-person job, requires advanced carpentry skills, and even knowledge of household electronic systems.
Not only was the upward-lifting garage door and the electric garage door opener invented by Overhead Door Corporation’s founder C.G Johnson in the 1920s, but we also have a tradition in excellence for garage door repair, service and maintenance. Even with the most reliable products problems can arise and when they do it’s important to know who to contact to fix these issues while providing solutions to prevent future complications.
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.
Replacing torsion springs is done with the door closed. You start by carefully unloading all of the springs (most standard-size doors have two; any broken spring will already be unloaded), using the winding bars. Then, you unbolt the springs from the central rod bracket, disconnect the cables from the pulleys, and loosen the pulleys and slide them off of the rod. Next, you swap out the springs, reinstall the pulleys and cables, and secure the inside ends of the springs to the central bracket. Finally, you wind up both springs (securing them with two setscrew bolts on the winding cones) and test the door for proper spring tension. Often, springs need an extra quarter-turn or two to get the door balance just right.
Since garage doors come in all weights and sizes, the right springs need to be installed in order to properly balance the door. If a technician puts the wrong spring on your door, not only will this damage your garage door system, but it will cause the garage door opener to do more work than it was built to do. This is why Precision technicians only install the right springs for the door's weight and check their work by performing a balance test.
NEVER use screwdrivers, pin punches or pliers handles to wind or unwind a torsion spring. Trust us: This is the best way to wind up in the hospital. Don't even think about doing this job without a proper set of winding bars. You can buy a set of professional hardened-steel winding bars for about $25 from online suppliers. (Garagedoorpartsusa.com and stardoorparts.com are two online sources that sell winding bars, springs and other parts.) Professional winding bars work with 1/2-in. and 7/16-in. winding cones. If your winding cones have 1/2-in. openings, you can make your own winding bars by cutting a 36-in. length of 1/2-in.-diameter round bar stock in half (buy round bar stock from any hardware or home center). Just file a smooth bevel on each end so it slides into the winding cone holes easier.
The following instructions for replacing garage door springs are for do-it-yourself homeowners and for maintenance repair men who service their smaller commercial or industrial sectional overhead doors. These directions are designed for torsion springs mounted to both sides of an anchor bracket above the middle of the garage door as pictured above. Instructions for replacing a single torsion spring, for replacing garage door extension springs, and for replacing Wayne Dalton Torquemaster springs are linked to our DIY Instructions page above. You'll also find a link for any other garage door parts you may need while repairing your door.
Another scenario is the garage door goes up very slowly when using the automatic opener. Some garage door openers have DC motors that start off slow when opening and then kick into a higher speed. If you have a broken spring, the opener might stay in the slower speed due to the heavy weight of the garage door. If this happens to you, close the garage door and pull the emergency release rope. Next, try to lift the door. If it is really heavy, then you most likely have a broken garage door spring.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.
Weather conditions can make rails expand or contract slightly, which requires a little extra pressure from the opener to compensate. Turning the force-adjustment screw increases or decreases the force. However, adjusting the force is not something to play around with unless you are confident you know what you’re doing. The force adjustment signals the opener to stop and reverse when objects are detected in the closing path. Too little force and just about anything will trigger it to stop, but too much force and the garage door might not respond to resistance from something or someone in the path when the door is trying to close.
Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.
With the Purchase of a Lift Master Garage Door Opener • Tighten & Replace all loose, bad nuts & bolts • Adjust track • Adjust limit switches • Regulation check on all opener safety devices • Adjust force & sensitivity • Adjust chain if needed • Lubricate garage door & opener Must mention coupon at the time of service Cannot be used with other offers.
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.

After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.


We arrived at a rental property and tried to open garage door to get our vehicle in so we could unload luggage, etc. Could not open from outside. Went into house and, from inside garage, tried automatic opener but this did not work. So in trying to open the door manually, I reached up and pulled on the red cord attached to a lever. What I could not see, and was not expecting, is that the rope was frayed through almost completely. The rope broke when I applied some weight to it, sending me backwards onto the floor of the garage.
After you’ve ordered your new garage door, we’ll perform a site inspection to confirm your door size. We’ll contact you to schedule the installation, and our professional installers will do the rest. They’ll deliver your door, take down the old door, reconnect your opener if there is one, seal your perimeter and provide a final walk-through where they’ll clean up the area and haul away your old door. Additional fees for haul away may apply in some markets. We are happy to provide answers to questions you may have at the time of your garage door and opener installation.
Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.
Sears Garage Doors provides excellence in garage door repair services. With a Sears technician on the job, you’ll know that you’re getting the very best in industry experience and quality. Each of our employees undergoes a rigorous background check and extensive training to ensure quality results while on the job. Sears prides itself in offering some of the best experiences in customer satisfaction, service, and warranties. We believe in offering the best because we have the best customers. Call today to experience the best in what garage door servicing has to offer.
Sometimes, you’ll notice that your garage door closes all the way and then immediately goes back up instead of staying in the closed position. This issue usually arises with brand new garage doors that were just installed or older models that may need to be reset. If this happens, the most likely culprit is the open and close limit settings of your garage door opener.
Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Garage door springs can break for a variety of reasons. Extreme heat or cold, for instance, can stress the springs to the point of breaking, or it could be that normal wear on older springs could cause them to break. Whatever the situation, a broken spring can render your garage door inoperable. Your door will not be able to open or close when a spring is broken, and you should stand clear of your door until a professional can assess the situation and correct it.
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
We offer industry leading service performed by the best licensed professionals in the region. Whether you need springs replaced, a motor repaired or need a new panel on your door, our service workers will get the job done efficiently and effectively, ensuring that your door is back in working order as soon as possible. We also offer a wonderful preventative maintenance program. This is a cost effective way to ensure that you avoid future problems by having the small, unnoticed issues addressed right away.
If the door opens this way, then there’s probably something wrong with the garage door opener. It’s a good idea to make sure the opener is plugged into its nearby power outlet. Also, make sure the circuit breaker for the garage door opener hasn’t flipped to the “OFF” position. If it has, then there may be an electrical issue that your garage door specialist should check out. http://m.www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Sometimes, it's not possible to repair the garage door springs, and the only option is to replace them. Replacing garage door springs costs between $200 and $300 for a professional to complete the job. This includes the cost of the spring, which ranges from $40 to $100 for a torsion spring and $5 to $30 for an extension spring. Labor rates for this work average between $45 and $65, depending on the company and the region. The price can also go up or down depending on the type of door. Replacing the springs on a tilt-up garage door costs between $150 and $200, which is slightly lower than the same work on a roll-up garage door, which typically costs between $200 and $250.

Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
If your door feels heavy, it is likely that your springs have started to wear down and are no longer capable of bearing the weight that they once did. Now, don’t worry, just because a spring is starting to lose its strength doesn’t mean it will snap at any moment. However, simultaneously, a weak spring isn’t any safer to try and repair on your own.

10.7 Continue tapping until the cone moves out to the mark on the shaft. Continue holding the bar off the garage door and pulling back toward the center of the door. If the cone slips away from the mark, repeat this step. Keep an eye on the tape to make sure the bar doesn't slip out of the cone. If it does start to slip, rest the bar against the top of the garage door, insert a bar in the next hole and turn the cone up enough to make it possible for you to push the marked bar back into place.
Most garage doors have two springs installed at the same time, when one breaks it's safe to say the second spring's life expectancy has just about expired. In order to save you from future inconvenience, unsafe garage door practices, and damaging your garage door opener, Precision will usually recommend to replace both springs. If you've had the same tires on your car for a while and one blows out while you're driving, wouldn't you replace them both? It's extremely important to properly maintain equipment such as garage doors and automobiles.
When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.

Every thing the tech demostrated was helpful, he knew how to do his job even if his eyes were shut. Very knowledgeable, took time out to explain every detail about the install process. Very highly satisfied. A d would love to have him for future additional repairs. Would definitely recommend sears and would use you guys again thanks mr.technician for a job well done.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
Most doors come with electric door openers. After a while these openers malfunction and need to be replaced. If your opener is broken, you’re in luck. These repairs don’t cost very much and can be replaced easily. You might even be able to do it yourself. Learn how to replace your garage door opener in 15 minutes https://www.youtube.com/watch?v=HeaR6Yhx6IY.
Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.

Garage Door Repair In My Area Centennial Co 80016


I was having trouble with my old garage door and decided that it was finally time to get a new one. I called Overhead Garage Door after a friend recommended them to me and I couldn’t be happier with the results. Overhead Garage Door was at my house immediately and the service was very professional and thorough. I would highly recommend this company to anyone who is looking for a new garage door or needs repairs done. I will definitely be using them in the future.

Garage Door Repair Estimates Centennial Colorado 80015


Sears Garage Doors provides excellence in garage door repair services. With a Sears technician on the job, you’ll know that you’re getting the very best in industry experience and quality. Each of our employees undergoes a rigorous background check and extensive training to ensure quality results while on the job. Sears prides itself in offering some of the best experiences in customer satisfaction, service, and warranties. We believe in offering the best because we have the best customers. Call today to experience the best in what garage door servicing has to offer.
Sometimes, people unplug their power source and then wonder why their garage door opener fails to work. Sounds ridiculous, I know, but it does happen. Make sure that your garage door opener is plugged into a working outlet. Outlets sometimes go out without warning, so you can check to see if the outlet is working by plugging another working electronic device into it. Also, check your circuit breaker, fuse, or GFCI.
Garage doors are the largest moving object inside your home. If you have a problematic garage door, it compromises the safety of your family and home. Ankmar Denver is a professional company you can count on. We provide you with quality service at a reasonable price. We offer FREE estimates on replacement garage doors and are spring replacement specialists. 24 hours a day 7 days a week we are your number one garage door repair service.

Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.
Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener.
If a roll-up door, assuming you have not put in cabinets or anything that prohibits sliding the shaft sideways about 2-3 feet out of the spring to change it, then about $200-250 should do it for a 2-car garage door. If he has to disassemble the brackets to remove the springs because the shaft cannot slide sideways enough to get the springs on/off, then probably another $50-100.
However, in addition to potentially causing injuries to the under-prepared DIYer, a malfunctioning door can become a safety hazard to you and your family. Keep in mind, according to the National Electronic Injury Surveillance System (NEISS), over 13000 people checked into hospitals with garage related injuries in the United States in 2007. You don’t want to turn a loved one into a statistic just to save a few dollars!
Quite a few garage doors come with manual locks, especially older models, for added security for your house. These typically look like a knob or handle in the middle of your door with two bars running horizontally from each side. There may be a small button on the top or side of the handle that you can press to slide the bars across the doors, thus locking the garage door from the inside. It can be somewhat easy to accidentally hit that button, especially if you’re getting large objects out of the trunk of your car near the door.
You can reschedule or cancel your service at any time. To reschedule, simply go to Your Orders, find your service order and click on the ‘Contact Provider’ button on Your Orders page. To cancel, click on the 'Cancel Order' button on Your Orders page. Payment goes to the pro from your secure Amazon account. Because you aren't charged until the actual work is completed, cancelling a job doesn't require a refund.
While there are times you may be able to fix the problem yourself, there are many reasons it may be best to leave the garage door repair up to the professionals. Knowing what’s wrong with your garage door may help you to determine if it is a problem you can tackle or if it’s time to call someone for assistance. To help you troubleshoot your garage door issues, here are the top 10 reasons your garage door won’t work.

Affordable Garage Door Repair Centennial Colorado 80015


Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX
6.4 Test the fit of the bar in the cone before loosening a set screw. Insert one end of your winding bar into one of the holes of the winding cone. Pull down on the bar slightly to make sure the set screws are tight. Position your ruler between the bar and the garage door. Move the bottom of the bar from side to side and measure the play. It should be less than an inch and a half. If it is over 2" either get someone else to change your springs or have someone make some bars that will properly fit the cones.
×