High-Cycle Springs: For longer lasting performance, choose our 100,000* high-cycle springs that are now powder coated. These springs are larger in length and inside diameter, resist rust, last longer than traditional springs and are guaranteed for life. Great for larger families, multiple vehicles and where the garage door is used more like your front door.
Check your garage door rollers to see if they have come off their tracks. If no damage has been done, a tech should be able to easily place them back on. If the track has become bent, however, it must be repaired and possibly (depending on the amount of damage) replaced. Don’t operate your door if it's off track or your track is bent. Your door could become seriously damaged.
If your garage door is equipped with extension springs (usually seen on single car garages), the cable and pulley might be hanging down when the spring break's. Extension springs use a two pulley system on each side of the door to lift the garage door up and down. When the spring break's everything goes haywire, causing the cables to become twisted or even frayed when they catch on the metal edge of the track. There is a lot of force being released when a garage door spring breaks.
Extension springs are long, lighter-weight springs that run perpendicular to the door and are mounted above the horizontal portions of the door tracks. These springs are tensioned by stretching out, using cables and pulleys, as with the torsion system. Because extension springs are merely suspended between two brackets (they are not mounted to a rod, like torsion springs), they must have a safety cable running through each spring. This helps contain the spring in the event of a breakage. Without the safety cable, a spring breaking under tension is a very serious safety hazard. If you have old springs that don't have safety cables, you should install them even if you aren't replacing the springs. https://m.youtube.com/v/Z_eZc-kh40c
6.13 Lower the second bar to the top of the garage door as you did the first bar. If your shaft is distorted inside the cone, you may need to tap the bar with a hammer as you unwind the spring. Maintain a firm grip on the bar; keep it firmly inserted completely into the cone; and be prepared at all times for the cone to slip, break, explode or snap loose from the shaft and jolt the bar down.
Torsion-spring doors have a drum-like pulley at each end of the metal rod that runs through the springs. Each pulley has a cable attached to the bottom of the door. The springs and pulleys are fixed to the rod so they all rotate together. When the door closes, the rod turns and winds up the springs, creating tension. When the door opens, the springs release the tension and turn the rod in the opposite direction.

You may remember a time as a kid when you and your siblings would close the garage door and run underneath it as fast as possible to make it out before the door closed. Well, on any garage door installed after 1993, that’s no longer possible thanks to two tiny photo eyes on either side of the garage entrance. These photo eyes transmit an invisible beam between each other that detects if anything is in the garage door’s path when it closes. This safety measure is there to prevent automatic garage doors from closing on top of someone or something and causing serious injury or damage to property.
Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up.

Garage Door Repair Emergency Centennial Colorado 80016


Step 1: Check the metal tracks inside the garage. Look at the mounting brackets that hold the tracks to the walls. If they're loose, tighten the bolts or screws at the brackets. Working inside the garage with the garage door closed, examine the tracks for dents, crimps, or flat spots. If there are any damaged spots, pound them out with a rubber mallet, or with a hammer and a block of scrap wood. If the tracks are badly damaged, they should be replaced.
4.4 Take the spring on the left and place it at the left end of the door as pictured here. Notice that the end of the wire points to the right toward the center of the door. This is a right wind torsion spring. It will go above the garage door on the left side of the spring anchor bracket. The winding cone at the other end of this spring is usually painted red.

Aaa Garage Door Repair Centennial Co 80016


If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
×