Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!! https://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

8.5 Inspect the bearing. Lube it with motor oil, spray lithium, or spray lubriplate grease. Do not use WD-40. If the shaft is worn and the bearing is seized and you can't free it, replace the bearing. Or, if you have bearings labeled "ADH" we recommend replacing them. I find very few other bearings that need to be replaced. However, if you do need to replace the bearing and you do not have a new one, you can replace it at a later date. You'll find a quick way to do this at our End Bearing Plate Replacement instruction page. http://www.youtube.com/watch?v=Z_eZc-kh40c
Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.
If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot. http://youtube.com/v/Z_eZc-kh40c
I PAID 700.00 DOLLORS TO GET THE 2 SPRINGE REPLACED WITH TOW DIFFERENT SPRINGS AND BOTH END BEARINGS PLUS INSTATTING THEM. tHIS IS ON A SATURDAY EVENING. aFTER ALL THAT i PAID BY CREDIT CARD THA THE INSTALL COULD SWIPE ON HIS PHONE. hE SAID AT THAT TIME I WOULD RECIEVE MY INVOICE VIA EMAIL. I didn,t think about it until another repair man came today 3/9/16 and he showed me that the bar that goes from one side to the other, had a bow in it of 3 inches just frome one side to the other. With this it will make the new bearings ware out faster. I trusted them to do the job right, But when i called to tell them that they replied that it was passed the 30 day warranty and they would do nothing more.

Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them. http://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.

I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:


To make sure the job gets done right, our professional installers are local, licensed and insured. With a 9.7 out of 10 VOC score, our garage installers will exceed your expectations, provide reliable service, and install attractive garage doors that will transform your home’s appearance. All labor, products and installations are 100% backed by The Home Depot. Service you can trust. http://youtu.be/Z_eZc-kh40c
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.

Garage Door Repair Emergency Centennial Co


If your photo eyes are clean and the door still isn’t closing, the next thing you’ll need to do is check the alignment of the eyes. The eyes should be pointing in exactly the same direction and at the same angle. If they’re off, they won’t register that the other one is there, and it’ll assume something is in its path, causing the door to stay in the open position. When checking the alignment, measure the height of each photo eye from the ground. Use a level to make sure they’re pointing directly across at each other at the same angle. A laser level will make this part a little easier, but if you don’t have one, a regular level will work as well.


Professionals can replace garage door springs in an hour or two. When you hire a pro, make sure to ask about the quality of the springs they will install. They may well offer several grades of springs to choose from, at a range of costs. Top of the line springs may be guaranteed for life, while economy springs can be expected to last perhaps five years under normal use.
Overhead garage doors weigh hundreds of pounds, and doors that are not properly maintained or which are equipped with older automatic garage door openers can be safety time bombs. All too common are the tragic stories of garage doors injuring or even killing children or pets who found themselves underneath a closing door. Modern automatic door openers with auto-stop and auto-reverse mechanisms have greatly reduced such accidents, but mishaps can still occur if the door and door opener are not properly maintained. http://youtube.com/watch?v=Z_eZc-kh40c
Next, if you don’t find an obstruction, check the springs. If your door has torsion springs, which are horizontal at the top of the door, you can tell they are broken by checking for a gap between the two springs. If your door has extension springs, you can check by looking to see if they are hanging on the side of the door. If you have a broken spring, you’ll need to call a pro to replace it as this is a dangerous task.
Garage doors provide one of the major entryways into your home. Therefore, it is essential to ensure that they are secure and in good working order. If you are having problems with your current door, then you need to have a professional determine if it can be repaired or if it will need to be replaced. Here are some of the most common factors that will affect the cost of a garage door repair.
I told several people that I planned on installing a garage door torsion spring after mine broke. ALL of them told me that it was too dangerous and a few feared for my life! Honestly it was one of the simplest home repairs I have ever done. That is thanks in large part to your very helpful installation video. Your videos on measuring springs etc. were also very helpful. All of the necessary details are there.

The following instructions for replacing garage door springs are for do-it-yourself homeowners and for maintenance repair men who service their smaller commercial or industrial sectional overhead doors. These directions are designed for torsion springs mounted to both sides of an anchor bracket above the middle of the garage door as pictured above. Instructions for replacing a single torsion spring, for replacing garage door extension springs, and for replacing Wayne Dalton Torquemaster springs are linked to our DIY Instructions page above. You'll also find a link for any other garage door parts you may need while repairing your door.


Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.

Springs are one of the primary components in all garage door systems. Torsion springs are usually mounted horizontally over the door opening. As the door closes, cables add tension to the springs and as the door opens that tension is released. The opening of the door causes the springs to unwind in conjunction with the weight coming off the door. This achieves a natural buoyancy. However, as the door moves up and down over time and the cycle count rises, the steel in the torsion springs will grow weak and will no longer be able to create energy or lift your garage door.

Garage Door Repair Centennial Colorado


Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break.

Garage Door Repair Images Centennial Co 80016


Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]

If you are not sure if your door had the correct springs, we recommend that you weigh your door using an analog scale. From my own field experience I would estimate that at least 10% of the doors have the incorrect springs on them. In addition to this, most manufacturers spring their doors using a 20 pound window. We like to improve the garage door balance.
The spring system opens and supports the garage door. These springs are under heavy force, which allows the door to bounce back open and avoids overburdening the garage door opener with the entire weight load. If these springs are stuck or broken, the whole system is affected. Start by lubricating the springs with non-silicon-based lubricant. If this fails, disconnect the garage door opener from the garage door to manually open the door. If you experience significant resistance, the springs might need to be replaced; a job that requires a professional.
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.
There are knobs or dials located somewhere on your garage door motor that you can use to adjust the limit settings. The exact location and resetting procedures will vary depending on the brand and model of garage door you have. Your owner’s manual should have more specific information on how to adjust your limits. You may need to experiment with a few adjustments before finally getting the correct setting. If you find that adjusting the limit settings isn’t working, it might be time to call a technician to come and help get your garage door to stay closed.
Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly.

Garage Door Repair Estimates Centennial Colorado 80016


Just like car tires are rated by miles, garage door springs are rated by an estimated number of cycles (1 cycle = your garage door going up AND down 1 time). The springs used by our competition range anywhere from 5,000-10,000 cycles, whereas we use a high-grade steel spring rated for 25,000-50,000 cycles! This is why we can put, in most cases, a Lifetime Guarantee on our springs for as long as you live in your home!

Aaa Garage Door Repair Centennial Co


It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
Nate was very courteous and professional and called to let me know that he was about 30 minutes from my house. I had purchased a new Sears garage door opener, but when Nate arrived at my home, he inspected the existing unit and told me that it was still in good shape except for a worn out part. Nate procured the new part and brought it to my home this morning. The unit was repaired in about 10 minutes! The existing unit was just over five years old, so I'm glad I will get some more use out of it.
Wheel Track Obstruction – Try closing the garage door manually to see if there are obstructions on the wheel tracks. If that is not the case, examine your tracks for potential damage like dents and bends. Look at your door to see if it is hanging unevenly. If the track is damaged or the door is hanging unevenly, it is time to call a professional for repairs. Track repairs can typically cost $133 to $154. Cost for correcting the uneven hanging of doors themselves can vary greatly, but typically cost about $125.
Slide the left spring onto the tube and add the cable drum. When your new springs arrive, put the new left spring (the 1 with the end facing up and to the left) on the torsion tube, making sure that the stationary cone on the end of the spring faces the center bracket. After sliding the new spring into place, replace the cable drum and insert the torsion bar into the left bearing bracket.[9]
We lead busy and sometimes hectic lives. It’s easy for someone low on sleep and high on stress to accidentally bump into their garage door leaving a little damage. If you’re lucky it’s just an individual garage door panel that’s been damaged. This will leave you with the option of garage door panel replacement. There’s a chance it might cost you upwards of $150-200 to spot repair damaged garage door panel. If it happens to be an in-production model, they probably will be able to repair or replace the entire panel (if needed) for $250-400. Unfortunately if you’ve got an older model of garage door the panels may no longer be in production. This might seem like a disadvantage because you’ll end up having to just replace the entire door. Many times it’s actually easier and more cost effective to just replace the garage door.
A1 Garage Door Service is the trusted service provider in installing, servicing and repairing all kinds and types of garage doors. We encourage you to check out the reviews of the people of Albuquerqueon the kind of garage door service that we provide. Our customers have consistently given us A+ ratings on BBB, 5-star ratings on Yelp and the Super Service Award on Angie’s List to express their satisfaction on our service.
Aging garage door springs cause the door to effectively "weigh" more as the steel loses its resiliency. With new springs, a heavy garage door should take no more than about 10 pounds of force to lift into an open position. With springs nearing the end of their lifespan, the force required to lift the door can be considerably more, since a garage door may weigh 200 pounds or more.
×