In the home improvement world there's a common recommendation regarding garage door spring repair: always leave it to the pros. This is sound advice, but it's not as hard-and-fast as most sources claim. The fact is, a handy homeowner who's competent with tools and has a basic understanding of mechanical systems can replace either type of garage door spring. The procedures are pretty simple, but they involve many steps that must be done in the proper order, just like the pros do it. It's also critical that you get the proper size replacement spring. If you think you're up to the task, look at online tutorials by garage door pros to see what's involved. Helpful videos explain how to measure your old springs and order the correct replacement size as well as how to do the job from start to finish.

Garage Door Repair How Much Centennial Colorado 80015


Garage door springs come in two styles: torsion (see above), which mounts on the header above the door, and extension (Photo 1), which floats above the upper roller track. In the past, extension springs were safer to install but didn’t have containment cables running through the center of the spring. Without cable, these springs become dangerous, heavy whips when they break. They also tend to be noisier than torsion springs, and we recommend you use them only if you don’t have the 12 in. of headroom above the door that a torsion spring requires.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.

Noisy garage doors cause all kinds of problems, especially for anyone who has to sleep above or next to the garage. Fortunately, most noisy garage doors can be fixed with a combination of routine maintenance and the replacement of a few parts. If the basic maintenance tips described above don't quiet a noisy garage door, it's possible that the door's hinges need to be replaced.
Just like car tires are rated by miles, garage door springs are rated by an estimated number of cycles (1 cycle = your garage door going up AND down 1 time). The springs used by our competition range anywhere from 5,000-10,000 cycles, whereas we use a high-grade steel spring rated for 25,000-50,000 cycles! This is why we can put, in most cases, a Lifetime Guarantee on our springs for as long as you live in your home! http://www.youtube.com/v/Z_eZc-kh40c?version=3
10.8 After the cone reaches the mark, continue pulling the bar off the garage door and back toward the middle of the door with your left hand. Tighten both set screws 1/2 to 3/4 turns each after each screw first meets the shaft. This is the point at which you will feel the screw meeting resistance. If the garage door spring snakes after tightening the set screws, repeat the process and stretch the spring half as much as before. Residential torsion springs are stretched 1/8" to 1/4". Larger commercial and industrial overhead garage door torsion springs are stretched as much as an inch.
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.
DIYers are generally steered away from working with torsion springs because installed springs are always under tension. To safely remove a torsion spring, you have to control the tension by holding the spring with a solid metal winding bar, then you loosen the spring from the rod and manually unwind the spring using two winding rods. The spring is potentially dangerous until it is fully unwound. By contrast, extension springs have little or no tension when the garage door is fully open.

A1 Garage Door Repair Centennial Colorado 80016


2.3 Beware of older winding cones. These older Crawford and McKee torsion spring cones were made for 5/8" bars. Sometimes, however, the holes are too small for 5/8" bars. Whatever you do, don't use a 1/2" bar; instead, grind down a 5/8" bar to fit. I recently had a McKee spring let loose after winding because I used a 1/2" bar when my 5/8" bar wouldn't fit. Just before it let loose I was telling myself, "This is not safe." And it wasn't. The only safe way to replace these older springs is to make a winding bar for each hole of each cone.
It's a great idea to hire a professional to do your garage door opener installation for a few reasons. First of all, a pro can often be the most time-efficient way to handle the garage door opener installation, because a pro will have the right tools and experience to make your garage door opener installation as swift and smooth as possible. Secondly, a pro garage door opener installation will include making sure all the required garage door opener mounts and sensors are put together properly. A great garage door opener installation will include using the manufacturer’s recommended method of assembly and optimal placement of the garage door opener mount and sensors. Find top-notch garage door opener installation pros on Amazon Home Services and you'll see professional garage door opener installation services at competitive prices. Secure convenience and peace of mind by getting a professional garage door opener installation for your home. You'll never regret adding a garage door opener installation project to your to-do list. If you’re the kind of person who doesn’t have the time or patience to do your garage door opener installation, don’t worry. Because you don’t have to if you don’t want to. Amazon Home Services has you covered, to do your garage door opener installation quickly and professionally. Just schedule the garage door opener installation pro of your choice from our list of top-rated service providers.
Product was received in two days and was as advertised. Installing these myself saved around $150 but it took around 2-3 hours. I would imagine everyone's experience is going to be different. These springs appear to be heavier duty than the ones they replaced. I couldn't use the same slots for tension as the old ones and it was trial and error in adjusting the length of my pull cable until the door closed as it should. I need to replace the springs on my other garage door and would think that will take less than an hour based on what I learned from the first install.
If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.
If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
First, make sure your transmitter isn’t stuck under something that could be pressing on the button. For example, your transmitter may have fallen under your car seat and the button is accidentally being pushed by something heavy rolling around on your floor. If that’s not the case, you may also need to check your transmitter’s frequency. It’s possible your neighbors could be running their garage doors on the same frequency as yours, and as they drive by, they’re opening their garage door along with yours.

When you're done watching this video you'll know how to determine whether the company you hired to replace your garage door spring installed the right size spring on your door. You'll also learn the consequences to your garage door opener if the wrong size spring is used. If you are having a problem with your garage door spring, the 2:30 minutes you spend watching this video is time will spent.
In this article, we’ll tell you the difference between a safe door and one that’s unsafe. We’ll also give you the helpful tips you’re not likely to find in the manufacturer’s instructions to correctly, and safely, install a new garage door with a torsion spring and do-it-yourself tensioning. Installing a new, double garage door yourself will save you several hundred dollars and should take eight to 12 hours if you’re fairly handy. You can do most of the new garage door installation project yourself, but you should recruit help for removing the old door. http://www.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
Every modern garage door is built with a sensor due to a mandate passed by the government back in the 1990’s that required garage door opener manufacturers to install safety devices. To meet this mandate, most garage doors have a sensor installed on each side of the doorway. They are often referred to as photo eyes since their main function is to maintain visual contact with one another. If that visual contact is broken by an obstruction, then the garage door stops in its tracks. This is meant to prevent the garage door from closing on a vehicle – or even worse, a person.
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.

Just like car tires are rated by miles, garage door springs are rated by an estimated number of cycles (1 cycle = your garage door going up AND down 1 time). The springs used by our competition range anywhere from 5,000-10,000 cycles, whereas we use a high-grade steel spring rated for 25,000-50,000 cycles! This is why we can put, in most cases, a Lifetime Guarantee on our springs for as long as you live in your home!

Aaa Garage Door Repair Centennial Co


DoItYourself.com®, founded in 1995, is the leading independent home improvement and repair website. We welcome your comments and suggestions. All information is provided "AS IS." Website operating problems contact [email protected] Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Copyright© 1995-2018 MH Sub I, LLC dba Internet Brands. All rights reserved. You may freely link to this site, and use it for non-commercial use subject to our terms of use. View our Privacy Policy here.
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.
Garage door springs are part of the garage door, and they're the first part to check when the door doesn't work; they malfunction more commonly than other parts of the door. In fact, the door cannot open or close with damaged springs. They raise and lower the door using one of two different methods: torsion or extension. The traditional choice for garage doors is extension springs, which sit above the door's horizontal track. They're more affordable than tension springs, making them a popular choice among builders, but they have more exposed parts and are more likely to break than tension springs. For this reason, extension springs must have safety cables to support them if they break. Tension springs attach to the wall above the garage door and work by twisting spring coils around the shaft as the door moves. These springs can support more weight than extension springs and have fewer exposed parts so they last longer.

Garage Door Repair Cost Centennial Co 80016


Start your garage door spring replacement project by getting a rough measurement of your springs (length and diameter). Then measure the width and height of your door. Make sure the quote includes the trip charge, parts and labor. Then ask for a price based on 7x19 lift cables and double-life springs. Those items will give you more years of service and should only add $65 to the price.

When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.

Garage Door Repair Near Me Centennial Co


Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.

Garage Door Repair Guy Centennial Co 80015


Garage doors make life easier, particularly when you’re arriving home in the middle of a rainstorm. It’s easy to take the convenience a garage door provides for granted -- until it stops working properly. The door loses its visual appeal instantly, stuck there half-open. This type of situation also raises security concerns as a simple trip to the store can become a headache. Simple fixes when a garage door gets stuck halfway may prevent it from happening again. http://youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c

I was disappointed with the pressure of a tub and shower that were plumbed with 1/2 supply lines (2nd floor). Could be low pressure from the street, but I want to replace with 5/8. Plus, I'd like to have 2 back to back showers, one inside and one outside. So, I had intended to bring a 1 supply to both, then branch up to valves and shower head with 5/8. Finally, I thought pressure from the street was typically 55 to 70 psi and I am concerned if pvc can take that.Any thoughts?
We arrived at a rental property and tried to open garage door to get our vehicle in so we could unload luggage, etc. Could not open from outside. Went into house and, from inside garage, tried automatic opener but this did not work. So in trying to open the door manually, I reached up and pulled on the red cord attached to a lever. What I could not see, and was not expecting, is that the rope was frayed through almost completely. The rope broke when I applied some weight to it, sending me backwards onto the floor of the garage.

Remove the clamps and pliers from the torsion tube and track, and lift the door about 3 ft. by hand. If the door springs are properly adjusted, the door should stay in place when you let go. If the door falls when you let go, add a quarter turn to each spring. Repeat if necessary. If the door continues to open on its own, release spring tension in quarter-turn increments until the door stays in place when you let go. Then reconnect the opener. https://youtube.com/e/Z_eZc-kh40c


Garage door torsion springs are usually the first to break or give out among the many components of your garage door. This is because the springs bear a lot of pressure, supporting the entire weight of your garage door which can oftentimes be quite heavy. Through regular and continued use, garage door springs are usually stretched tight and subject to wear and tear.
Finally, we also carry any and every residential garage door product that you need to have a state-of-the-art, secure and safe garage door. We are proud certified dealers of Clopay doors, the most durable and versatile doors on the market. With over fifty years of garage door manufacturing experience, you can trust Clopay quality, just as you can trust our team to install these highest-quality doors.

Garage Door Repair Guy Centennial Co 80015


On average, to have your springs replaced on your garage door will vary anywhere from $200 to as much as $400 if you were to hire a professional.  Breaking the costs down, the springs, depending on the part needed and the size, will cost about $20 to $60 each.  Add in the labor, which can be $45 to $85 per hour, depending on your location, can bring the grand total to the estimate noted.   A tilt-up door, on average, will be about 20 to 30 percent less than a roll-up door.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

If one of your door springs just broke and you are looking for instructions to decide if you can change the spring or springs safely and correctly, this page should help. DO NOT OPEN AND CLOSE YOUR GARAGE DOOR. Wooden garage doors are heavy and will probably damage or ruin the opener. The tops of steel doors often bend when operated with broken springs.
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
On one-piece doors with side springs, you open the door to relieve the spring tension, and simply swap out the springs on the opener-arm mechanism; there are no cables or pulleys to deal with, and the springs have internal safety rods. Some doors have tensioners that maintain moderate tension when the door is open all the way, and on these you'll have to loosen the tensioner in order to remove the spring.
10.8 After the cone reaches the mark, continue pulling the bar off the garage door and back toward the middle of the door with your left hand. Tighten both set screws 1/2 to 3/4 turns each after each screw first meets the shaft. This is the point at which you will feel the screw meeting resistance. If the garage door spring snakes after tightening the set screws, repeat the process and stretch the spring half as much as before. Residential torsion springs are stretched 1/8" to 1/4". Larger commercial and industrial overhead garage door torsion springs are stretched as much as an inch.

Garage Door Repair And Service Centennial Co 80016


If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.
11.2b If the springs you installed are too strong, and if you wind the springs the correct number of turns, the door will not stay down nor half way. The garage door will be hard to close. DO NOT REMOVE MORE THAN HALF A TURN OF SPRING TENSION TO CORRECT THE PROBLEM. Here's why. If you remove 3/4 of a turn to get the door to stay closed, and then if you open the door, it will get heavier as you open the door, and once open, the cables will come off the drums. This could create as much as a day's extra work. It could also cause door damage and/or result in serious injury. Do not use the door! Get different springs!

If your garage door is not opening or has become jammed, you may need to replace the garage door cables. Unless you have the proper tools and know-how, this is a job best left to a professional due to the weight of the garage door and the extreme tension of the springs. The cost of repair will vary depending on your location, the length of the cables you need, and the time it takes the pro to do the replacement.


When you know you’re in range and the door still won’t open, check to make sure the antenna is hanging down from the motor inside your garage and nothing is blocking it. Your antenna must be free from any obstruction to clearly receive the signal to open and close the door. Also inspect the antenna for any signs of damage. If it looks like there has been damage to the antenna, you’ll need to call your garage door technician to come out and replace it.
Texas Garage Door and Opener in Plano, TX provides residential garage door and commercial overhead door services throughout Dallas, Fort Worth and the surrounding areas. Our fully insured team specializes in garage door installations, repairs and maintenance services. We have over 25 years of combined experience and qualified technicians ready to service your garage door needs. We are available 24/7 for emergency service, please call 972-633-3872 today! http://m.youtube.com/watch?feature=player_embedded&v=Z_eZc-kh40c
When you hire a professional, the first thing they will do is turn off the power as a safety precaution.  They will then measure the existing door springs to make sure the new springs they order or have in stock fit accordingly.  With these new springs, they will unwind the existing springs and install the new ones in its place, tightening them with screws.  When tightened, the springs will be balanced, lubricated and the springs will be wound up.  Lastly, the door will be tested and the tracks will be lubricated to move efficiently.

Aging garage door springs cause the door to effectively "weigh" more as the steel loses its resiliency. With new springs, a heavy garage door should take no more than about 10 pounds of force to lift into an open position. With springs nearing the end of their lifespan, the force required to lift the door can be considerably more, since a garage door may weigh 200 pounds or more.


10.8 After the cone reaches the mark, continue pulling the bar off the garage door and back toward the middle of the door with your left hand. Tighten both set screws 1/2 to 3/4 turns each after each screw first meets the shaft. This is the point at which you will feel the screw meeting resistance. If the garage door spring snakes after tightening the set screws, repeat the process and stretch the spring half as much as before. Residential torsion springs are stretched 1/8" to 1/4". Larger commercial and industrial overhead garage door torsion springs are stretched as much as an inch.

Garage Door Repair And Service Centennial Co 80016


Install the stiffening strut on top of the top section of steel doors with the section lying flat. Then install the opener bracket that replaces the center bracket between the top two sections. While you’re working on the sections, protect them from scratches by putting carpet scraps on top of your sawhorses. Now, slide the rollers into the roller brackets.

I had two extension springs replaced, all for $135.00 (this included tax). The work took about 35 minutes and I was relieved to have this taken care of. You never realize the importance of something to you, until it is broken. Was this a good price? Seemed reasonable enough and the repairman came out the same day I called. Harris County Houston, Tx.
The cost to repair a garage door is typically more affordable than installing a new garage door. Often, a garage door repair simply requires fixing a broken spring. The average cost to repair a garage door spring is $180, but prices range from $100 to $350 if the installer must disassemble the brackets to reach the springs. Common garage door repairs include lubricating or balancing the springs and installing safety cables that work as a backup for an extension spring system. Most homeowners can lubricate the springs on their own for the cost of the lubricant ($5 to $6), but many garage door contractors include lubrication services as part of their maintenance plans. Refitting existing springs to balance the door requires between 45 to 90 minutes to complete, with a price tag ranging from $75 to $110. Safety cable installation costs between $150 and $200.
If the track is misaligned, but the door still moves, there are a few things you can do to attempt to remedy the issue on your own. You’ll know that it’s misaligned if you hear a rubbing noise when the garage door reaches a certain spot on the tracks each time it opens and closes. Sometimes the door may even slow down slightly when it hits this spot.
Received all items as indicated, I would recommend purchasing a metal center bearing also, other Than the plastic that this comes with. Install was easy and strait forward. hardest part was finding how many turns to tighten those springs?? I used a general rule of thumb of a full turn for every ft. Of door. 4 quarter turns equals 1 full turn. I found that 26 balanced the door perfectly. These springs seem a little smaller than what was there however, the coil itself is the same. (Pic) After installing, I recommend oiling the springs with some motor oil. This will help with rust and noise. Good luck with yours, it's worth the work for the saving!!
There’s another reason new doors are superior to old ones: energy efficiency. Keep in mind, garage doors are large, and when they open, they let a lot of outside air into your home. While you may have significant insulation separating your garage from the rest of your home, eventually that temperature differential will start to influence your energy bills. http://youtube.com/e/Z_eZc-kh40c?app=desktop

The average lifespan of torsion springs is determined by its cycle count. Garage Door Medics provides springs with an average of 25,000 cycles and we can provide custom size springs for any door. The industry standard is 10,000 cycles. When a garage door is used more frequently, the springs may not last as long. If you begin to see signs of wear, it’s time to give Garage Door Medics a call!
10.3 At this point you will wind the spring. Notice that the end of the spring on the winding cone points up when facing you. You will wind both springs up and counter intuitively as if you are trying to unscrew the winding cones from the ends of the springs. Begin by turning the spring up 1/4 turn until it meets resistance. This is your first quarter turn. Count "one." Next, insert the bar and raise it 90 degrees. Insert the second bar. This is "two." As you wind the spring it should grow in length the thickness of one coil for every turn. The cone should cover your mark after the first couple turns. Many garage door tradesmen mark the torsion springs with chalk or paint, but this often generates confusion.
From a big-box store, basic garage door cables can run between $8 and $20, depending on the product. Your pro may charge you a different cost if they provide the cables. Your cables may not need to be replaced if they have simply come off the track, but broken cables will need to be completely removed and replaced. In either instance, the pros will need to secure or take down the door; unwind the springs; reset or replace the rollers, cables, and drums; and then wind the springs once more. For example, a pro could reset cables that have come off the track for $129.99. The average national cost for a garage door repair specialist is $80 - $110 per hour and the typical cost to replace a broken garage door cable is anywhere from $130 to $200.
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
You may enter your information on this website, visit an in store associate or call our garage door repair team at the number at the top of this page. Within 24 hours you will receive a call from a local service provider to discuss your requested service. Afterwards, you will schedule a date and time for the service provider to come to your property.
If the door won’t move at all because of an alignment issue, then this problem isn’t one that you should try to tackle yourself. A garage door professional will have the necessary equipment needed to safely realign and repair your garage door. Additionally, if the track misalignment is beyond repair, a professional can install a new garage door track for you.
6.8 Properly tightened screws will loosen with less than a turn. Once you loosen a set screw, keep at least one bar in the cone AT ALL TIMES until the spring is fully unwound. Many cones have been over-tightened. The spring may unwind 1/4 turn and not unwind any more until one of the set screws is loosened some more. You may need to completely remove the set screws. The shaft may be distorted and the cone still may not unwind at all.

Garage Door Repair Bracket Centennial Co


The springs are an essential component to your garage door in that they enable the door to be lifted or lowered easily, despite its weight. If either of the springs are broken, then the door will become stuck. There are two types of garage door springs – torsion springs and extension springs. Torsion springs are located near the top of the door, whereas extension springs are located on each side of the door. If your garage door uses torsion springs, check for a gap between the springs to identify whether they are broken. If you have extension springs, look to see if a piece of the springs are hanging from the side.

When a company tells you they're providing you a warranty of only 1-3 years, it means they could be using cheap hardware. We can provide a lifetime warranty on the hardware we use because it's superior to a traditional garage door company's hardware in a number of ways. We're so confident that our springs won't need replacing, if by chance one DOES break, our name is on the springs to remind you to call us to replace it for free!
Dallas Texas, Plano TX, Garland TX, Highland Village, Lakewood, Las Colinas, Lewisville, Little Elm, Grapevine, Haltom City, Hurst, Keller, Forney, Carrollton, McKinney TX, Murphy Texas, Oak Lawn, Arlington TX, Parker TX, Plano, Preston Hollow, Richardson TX, Denton, Addison, Allen, Bedford, Coppell, Crowley, DeSoto, Euless, Flower Mound, Rockwall Texas, Garland Texas, Rowlett TX, Sachse TX, The Colony TX, Lavon Texas, Fort Worth TX, East Dallas, North Dallas, Wylie TX, White Rock Lake, area Lakewood, North Richland Hills TX, Benbrook, Burleson, Waxahachie, Red Oak, Irving TX, Mesquite TX
If you have a 1-spring system, you can choose to upgrade to a 2-spring system. The 2-spring system will make your springs last longer since it balances the weight on two instead of just one spring. It is not required but recommended. To convert to 2-springs, you will first need to find the measurements of your one spring and then use the form on our website to convert to a 2-spring system or just contact us. We will take care of you 24/7 via our online support.
Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
×