SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

High-Cycle Springs: For longer lasting performance, choose our 100,000* high-cycle springs that are now powder coated. These springs are larger in length and inside diameter, resist rust, last longer than traditional springs and are guaranteed for life. Great for larger families, multiple vehicles and where the garage door is used more like your front door.
If the engine of your garage door opener isn’t working properly, then your garage door probably won’t be working properly. If your garage door gets stuck and you hear a grinding sound coming from the garage door opener, then there’s a good chance that there is an issue with its engine. That issue is that the main drive gear probably needs to be replaced. The main drive gear is most common of the garage door opener’s components to fail. It is a plastic gear that takes some know-how to remove and replace, which is why you should strongly consider hiring a professional garage door repair service for this particular issue.
Insulation, which increases energy efficiency and can help to lower utility bills, is crucial when a garage door is attached to the home. In this case, doors with high R-values are preferred. This means it has insulation that can keep the heat in. The higher the R-value, the better insulated your garage will be against outside noise and cold and hot air.
Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done.

Garage Door Repair Free Quote Centennial Colorado 80016


The average cost is $190 for 2 springs in the Detroit area. This is for steel doors weighing under 140 lbs or known as a standard spring which fits 90% of all doors. The remaining 10% are wood doors or large heavy insulated doors. Expect to pay an additional $60 - $100 for a set of these. Garage Door Companies rarely carry these springs on their vehicles or stock them. Therefore, they either buy them locally at a premium or special order them. Regardless, its an additional trip that gets figured into the cost.
So your garage door is acting up, but you aren’t sure what the problem is. Maybe the door spring is one possible culprit, but you’re not sure if that’s actually the problem or if it’s something else. In this quick list, we’ll go through the most common broken garage door spring symptoms. If your garage door is exhibiting one or a few of these symptoms, there’s a good chance it’s broken and needs replacing.
For example, low headroom garage doors often have cable drums on the outside of the end plate and the torsion springs usually wind down rather than up. They normally have left wind springs mounted on the left side of the spring anchor bracket and right wind springs mounted on the right side of the bracket. The first part on the shaft beyond each torsion spring is the end bearing plate. Just beyond the end bearing plate is the cable drum. On these the cable often runs on the front of the cable drum. The bottom of the cable is attached to a bracket that wraps around the front of and outside the vertical track.

Garage Door Repair Free Estimate Centennial 80016


Align the upper roller tracks by carefully lifting the door halfway. Lock it in place with two locking pliers, and install the supporting brackets on the back of the rails using 1-1/4 in. perforated angle iron (available at home centers and hardware stores). Install 1-1/2 x 1/4 in. stop bolts, with the threads to the inside of the track, at the end of each upper track. http://www.youtube.com/v/Z_eZc-kh40c&feature=share

Over time, the springs in your garage door can wear down and break. While the average cost to repair garage door springs is between $100 and $200, in some cases you may need to replace them instead. Replacement can cost $20-$30 for springs plus labor which can cost up to $180. Here are some signs to watch out for when determining whether repair or replacement is the right course of action:


Snap a locking pliers onto the torsion tube to lock it into place while you tighten the drums. Rotate the drum to wind the cable into the winding grooves. Pull the cable as tight as possible before tightening the setscrews. Leave the locking pliers in place and repeat the tightening procedure on the other side. You want equal tension on both sides. Otherwise, the door will open unevenly.
Install new or use this right-wound torsion spring Install new or use this right-wound torsion spring to replace broken sectional garage door torsion springs. All DURA-LIFT springs meet the DASMA standard rating of 10 000 plus door open and close cycles. Both the winding and stationary cones are professionally installed for safe operation. Winding rod is included with ...  More + Product Details Close
Door styles - in addition to the styles just mentioned, it is important to also consider additional features such as windows across the top of the door to provide light inside of the garage, the use of steel or wood frames to give decorative doors added security and stability, and insulation which can reduce energy costs in the attached garage by an impressive 15 to 20%; and

Everyone wants to save money. Unfortunately, there are some areas you just can’t skimp on. This includes garage door springs. As much as it might be tempting to by smaller or cheaper springs, or maybe to buy one spring where two are needed, these attempts to save money will only end up costing more money in the end. When you buy the proper springs, they’ll last for years. When you cut corners to save money, the springs will wear out faster, meaning they’ll need to be replaced much sooner.
Professionals can replace garage door springs in an hour or two. When you hire a pro, make sure to ask about the quality of the springs they will install. They may well offer several grades of springs to choose from, at a range of costs. Top of the line springs may be guaranteed for life, while economy springs can be expected to last perhaps five years under normal use.
Inspect the area around your garage door to see if something is blocking the photo eye sensors. Then look at the tracks to see if there is any buildup on the inside. You’ll need to get a step ladder to look at the tracks on the top part of your garage, as it will be difficult to see from ground level. It may also not be a bad idea to proactively wipe down your garage door tracks periodically to prevent this type of buildup from occurring. Running a damp rag along each track should be enough to remove anything that’s lingering on the tracks.
Your springs may be broken. There are two different types of springs. If your garage door springs are located horizontally at the top of your garage door then it is called a torsion spring. You should check for a gap in between the springs to indicate if they are broken. If your springs are located at either side of your garage door, they are called extension springs. Look to see if a piece of them is hanging on the side of your garage door to indicate if those are broken. If your garage door springs are broken then replacing them is a dangerous process if you have never done it before so you should seek a professional to repair or replace them. http://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
All measurements should be in feet and inches. Step 1, measure across the existing door or desired space for the width, then up and down for the height. The rough opening of your space should be the same size as the door. Step 2, measure the sideroom, which is the space beside your door. Measure the width of the left side, and then the width of the right side. Step 3, measure the space above the door, which is called the headroom. Measure the height of the distance between the top of the door opening and the ceiling. Step 4, measure the ceiling, which is called the backroom. You’ll need to measure the distance of the garage door opening toward the back wall of your garage. You should have 6 total measurements in all once you’ve finished measuring the space. Keep in mind that having an automatic garage door opener installed might call for additional backroom or ceiling space.
One of the large springs on our garage door broke the day before Thanksgiving, trapping our van inside the garage. We have a daughter in a wheelchair and had lots of errands to run before Thanksgiving, so we really needed our van. We called Overhead Garage Door and they told us approximately when they would arrive. They not only replaced the broken spring, they replaced the other spring, all of the rollers and most of the hinges. They also replaced several rollers and hinges on the second garage door. The technician, Micah, and his brother could not have been nicer. The garage doors have never worked as well or been this quiet. I highly recommend Overhead Garage Door to anyone in need of new garage doors, or repairs to existing doors. A first class business.
First, check to see if the transmitter on the wall inside your garage still opens your garage door when pressed. If it does, then the transmitter in your car likely just needs a simple battery replacement. If you have more than one car transmitter for your garage door, then your other transmitters will likely need new batteries soon as well, since they were probably installed around the same time.
If the garage door is broken or damaged, it can affect the feeling of the entire house. It’s not only an inconvenience, but it can also make your entire house feel less sophisticated and less functional. If you happen to be trying to sell your house, this can seem like a major detraction. Even if you’re only having guests over, you may feel as though you’re doing less than putting your best foot forward by having a broken garage door.
When a company tells you they're providing you a warranty of only 1-3 years, it means they could be using cheap hardware. We can provide a lifetime warranty on the hardware we use because it's superior to a traditional garage door company's hardware in a number of ways. We're so confident that our springs won't need replacing, if by chance one DOES break, our name is on the springs to remind you to call us to replace it for free!

Garage Door Repair How Much Centennial Co 80016


Center and level the first section after you install the brackets. The door must be level even if the floor isn’t, so use shims under the section to level it. The rubber gasket on the bottom section will fill the gaps created by an unlevel floor. To hold the level in place, tape it to the section. To hold the section in place, lightly toenail a 16d nail into the frame and bend it over the section. Add brackets and rollers before setting them in place and stack one section on top of another, toenailing as you go up. https://www.youtube.com/attribution_link?a=Z_eZc-kh40c&u=%2Fwatch%3Fv%3DXXXXXX%26feature%3Dshare
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.

Garage Door Repair And Service Centennial 80016


10.6 Here you will need to do three things at once. With your left hand, lift the bar just off the top of the door and pull it toward the center of the garage door. While lifting up and back, tap the top of the bar just under the winding cone with your other bar. Pulling the bar back toward the center of the door as you tap causes the spring cone to bind on the shaft and not slip back.

Automatic Garage Door Repair Centennial 80016


If your garage door goes up and down in a jerky motion, you might have one broken spring on a two spring system. Some garage door openers are strong enough to lift a door with only one good spring. The “herky jerky” motion is especially common with garage doors equipped with extension springs. It might be something as simple as lubricating your garage door pulleys, hinges, and rollers. When in doubt or if something doesn’t feel right about your door, call a service company to have it serviced. https://www.youtube.com/v/Z_eZc-kh40c&feature=youtu.be
Most garage doors have two springs installed at the same time, when one breaks it's safe to say the second spring's life expectancy has just about expired. In order to save you from future inconvenience, unsafe garage door practices, and damaging your garage door opener, Precision will usually recommend to replace both springs. If you've had the same tires on your car for a while and one blows out while you're driving, wouldn't you replace them both? It's extremely important to properly maintain equipment such as garage doors and automobiles.
When you hire a professional, the first thing they will do is turn off the power as a safety precaution.  They will then measure the existing door springs to make sure the new springs they order or have in stock fit accordingly.  With these new springs, they will unwind the existing springs and install the new ones in its place, tightening them with screws.  When tightened, the springs will be balanced, lubricated and the springs will be wound up.  Lastly, the door will be tested and the tracks will be lubricated to move efficiently.
Sectional: Also known as a raised panel door, this door is the most common. It is made of several horizontal panels hinged together, fitted with wheels and mounted within a track. The biggest advantage of this door is it takes up relatively little space and easily controlled with a standard remote garage door opener for a nominal cost. Their moving parts are readily accessible which can keep repair costs low. The average cost for sectional door repairs is $128.
The technician, Robert Helton, was very pleasant, helpful, and professional. He repaired the garage door opener expeditiously and explained why it hadn't worked properly. He also checked the chain mechanism and the door itself and showed me how to manually work the door should I need to do that in the future. I was very pleased with this repair work.

Garage Door Repair Free Estimate Centennial Colorado 80016


Although garage door springs can break during any season and at any time, they most commonly break during the winter. This has to do with the temperature change. When the temperature sinks below a specific threshold, the metal will contract. This means it’s extremely possible for your door springs to shrink slightly during the winter months. This is hard on the springs and makes them more likely to break.

Garage Door Repair Images Centennial Co 80016


Garage door torsion springs are usually the first to break or give out among the many components of your garage door. This is because the springs bear a lot of pressure, supporting the entire weight of your garage door which can oftentimes be quite heavy. Through regular and continued use, garage door springs are usually stretched tight and subject to wear and tear.

Garage Door Repair Near Me Centennial Colorado 80015


Founded in 2011, Overhead Garage Door, LLC is a rapidly-growing garage door repair and installation company headquartered in Fort Worth, Texas. We serve both commercial and residential markets, and believe in the value of hard work and craftsmanship. We are fully licensed and insured and offer a broad selection of products to suit our customer's needs. As a family-owned and operated business, we put unbeatable customer service above all. This belief has allowed us to routinely expand into new markets and locations as we improve quality control and customer satisfaction.
Once the springs break, quite a bit of tension is put on the door cables, and they will often break next. When these cables break, they will snap and forcibly fly out like a broken rubber band. Think about how much it hurts to be snapped by a broken rubber band, and then multiply it by a hundred to account for the size and weight of the garage door cables.
If your garage door is equipped with only one torsion spring, it will be much harder to get your door open. You will need to get 2-3 people to help lift the door up because the full weight can be anywhere from 150 to 300 pounds. We don’t recommend lifting the door when the spring break's due to the danger of it falling on someone. If you absolutely must get your garage door open, raw strength is what you need. When you get the door in the up position, use vise-grips or a c-clamp on the track below the bottom roller to hold the door in the up position.
The low rating on the CS is due to the fact that inwas out of town and my wife called because the garage door wouldn't open. We had repairs to the only other exit, and the CS said because it could be opened manually, it was no emergency. She was stuck in the house for over Sixteen hours. No emergency crew came out. Steve, a tech who came out the first time, fixed the door. It is not his fault CS took their sweet time to help a 45 year customer. I commend Steve. I do NOT have anything good to say about CS.

Garage Door Repair Near Me Centennial 80016


We arrived at a rental property and tried to open garage door to get our vehicle in so we could unload luggage, etc. Could not open from outside. Went into house and, from inside garage, tried automatic opener but this did not work. So in trying to open the door manually, I reached up and pulled on the red cord attached to a lever. What I could not see, and was not expecting, is that the rope was frayed through almost completely. The rope broke when I applied some weight to it, sending me backwards onto the floor of the garage.
9.15 Install the bolts to secure the stationary center cones to the center bracket. Position the shaft here so it is the same distance from the header as the shaft is at each end. Finger-tighten the nuts until the stationary cones are flush against the center bearing plate. Forcing the cones by tightening the bolts may break a cone if it is catching on a bearing. Winding torsion springs with cracked cones can cause the springs to spin loose and the bars to fly. Secure the bolts.
Grab a tape measure and press the hook between two spring coils and note the length of 20 coils. Then measure 40 coils. Convert the measurements to a decimal (4-1/2 in. to 4.5 in., or 4-1/8 to 4.125, for example). Divide the two measurements by 20 and 40 to obtain the spring's wire diameter. Here's an example: 4.50 divided by 20 = .225-in. wire diameter; 9.0 divided by 40 = .225-in. wire diameter. If the two results match, you've measured correctly.
I went on Garage Door Nation website to look at the conversion chart from 1 to 2 torsion springs. For my 1 spring, size 2"/0.250ID/30.5" length, they recommended 2 of 2"/0.207ID/24" length. I got this kit from Amazon for $64 with $11 overnight shipping even though I could get free shipping through Prime over the weekend, but I couldn't wait for 3 more painful days. Installed it followed YouTube video. Worked better than my old one, a lot quieter. Check the video if you want to install one yourself. Professional installation costs hundreds of $$$:

Unlike torsion springs, replacing extension springs has long been given the "green light" for DIYers, primarily because you can complete the job without having to deal with spring tension. The general process is simple and safe: open the door to relieve the spring tension (and secure it open with C-clamps in the tracks); disconnect the spring from the track bracket and the spring pulley, and disconnect the safety cable from one end; install the new spring, reinstall the pulley, and reconnect the safety cable, and you're done. https://www.youtube.com/e/Z_eZc-kh40c


Instead, try other methods that might break the frozen connection between the door and the floor. For example, you can use a heat gun or hair dryer to melt the ice and free the door. Standard de-icing products can also work. And if you are careful not to damage the door or the seal on the bottom of the door, you can use a flat shovel or similar tool to chip away at the ice.

I'm getting a good laugh on all the comments on "Garage Door Nation" on how easy they or people make it sound to order and change out their torsion springs. First off, if you do your shopping, the savings is about $50 - $75 having a company do it. Is it worth the 3 days wait without the use of your garage door, the safety risk and your time doing it yourself? If yes, then go for it!

Wood - Wood garage doors are sturdy and quite beautiful. However, if you live in a humid climate, your doors will be prone to rotting and splitting. If your wood is painted, you must also factor in the costs of painting as part of your regular maintenance routine. The cost of repairing the wood varies depending on the type. However, average cost to repair a wood panel is $190 to $215.
If you're like most people, your garage door is your primary entrance to your home. It's convenient to use and parking in the garage provides protection from the elements. Garage doors have several moving parts, including the door springs that help raise and lower the door. These springs do eventually break down, leaving the door inoperable. When this happens, it's time to repair or replace the damaged parts. This cost guide shows you what it costs to hire a professional to repair or replace any garage door spring.

Garage Door Repair Emergency Centennial Co


Many jobs around the house are fairly easy fixes. It’s relatively easy to clean out your fireplace, clean the leaves from the gutters or repaint a wall. It’s a different thing to replace your garage door spring. It’s careful work that is almost impossible to do correctly the first time. Garage door professionals spend a great deal of time learning how to do it properly, and even the most detailed instructions won’t make you an expert in the span of a few hours. It can be almost infuriatingly annoying at times and is simply better left to professionals.
Loosen the set screws while holding each spring with a winding bar. Position a sturdy ladder to the side of the springs, rather than working directly in front of them, for safety reasons. Put on eye protection and leather gloves. Push a winding bar into the bottom hole of the winding cone on the outside of 1 spring. Use a wrench to loosen the 2 set screws. Keep a firm grip on the bar as the the spring will expand powerfully as the screws are released. Repeat on the other side.[2] http://www.youtube.com/e/Z_eZc-kh40c?app=desktop

With garage door installation costs, these numbers also include the actual purchase of the new door and other hardware, including the tracks, adhesives, connectors and fasteners. Keep in mind that if these numbers seem extreme, garage door replacement and upgrades can yield, on average, one of the highest returns on investments for homeowners — with an expected 85 percent.

If you want to do the repair yourself, get several phone estimates first, because rates vary widely among service companies. Most garage doors are heavy (200 to 300 lbs.), so call in three strong friends to help you lift the door and hold it open while you lock it in the full raised position with a locking pliers. Then move your vehicles and have your friends help you lower the door.
The following procedures are based on my 30 years in the garage door industry. In spite of my high mechanical aptitude, even after 18 years in the trade I lost the end of my left index finger. A few years later I had five stitches in my right thumb, and a year later five stitches in my left thumb. In 2004 emergency room staffs dug steel out of my eye and sewed up my ring finger with eight stitches. The best I can do is help you minimize the risk of injury; that's all I can do for myself. I am not so naive as to think that I have made my last trip to the emergency room. Repairing garage doors, particularly replacing torsion springs, is dangerous work, whether you are a do-it-yourself homeowner or an experienced technician.

Garage Door Repair Images Centennial Colorado 80015


Order replacement springs. Many manufacturers and distributors only provide torsion springs to professionals, and won’t sell them directly to the customer. Luckily, they are available on the Internet, so search online to find replacement springs. Make sure they match the coil size, length, and interior diameter of the springs you removed. Also, be sure to order both a “left-hand” and a “right-hand” spring as the coils are wound in different directions.[8]
If you are not sure if your door had the correct springs, we recommend that you weigh your door using an analog scale. From my own field experience I would estimate that at least 10% of the doors have the incorrect springs on them. In addition to this, most manufacturers spring their doors using a 20 pound window. We like to improve the garage door balance.

If you have decided to replace your springs, if you are sure your door had the correct springs, and if you are ready to buy new ones, we recommend that you measure your spring or springs following the instructions in Step 4 below. Measuring springs can be difficult; most individuals, even garage door technicians, sometimes have difficulty measuring torsion springs. Ordering incorrect springs wastes time and money.
×