The following instructions for replacing garage door springs are for do-it-yourself homeowners and for maintenance repair men who service their smaller commercial or industrial sectional overhead doors. These directions are designed for torsion springs mounted to both sides of an anchor bracket above the middle of the garage door as pictured above. Instructions for replacing a single torsion spring, for replacing garage door extension springs, and for replacing Wayne Dalton Torquemaster springs are linked to our DIY Instructions page above. You'll also find a link for any other garage door parts you may need while repairing your door.
Guest 9232954 -- check out the other answers for this question, and the links below the answers for even more - seems from $125-400 range from different contributors (should be replaced in pairs for balanced lifting unless one spring is quite new), about $200-250 or 300 seems a common charge. The springs themselves generally run about $20-50 each depending on lead they have to carry.
Usually, when a garage door spring breaks the door has already closed or come down. In some instances, however, a spring can snap while the door is closing or in motion, causing the door to fall rapidly. In these situations, the door can become a safety concern for you and your family, so you should keep your distance and call a garage door professional as soon as possible. Garage doors are very heavy and can cause injury if not handled properly. When a garage door problem occurs, call a Sears Garage Door expert to help.
When it comes to garage doors, functionality and safety are equally important in the eyes of Sears Garage Door technicians. Our associates know the importance of garage door safety and the hazards that a faulty garage door can pose for your family. To confirm that your garage door and opener operate safely, our technicians perform a 20-point safety check during maintenance calls and repair jobs. This safety check verifies that any repair work performed has been done correctly and that there are no lingering safety problems with your door and mechanisms. If our technician discovers any safety concerns, he’ll advise you on the best way to proceed with correcting the problem.
One thing to consider - assuming you have 2 springs and an opener, unless the other spring is quite new, you should replace it at the same time, first because it will probably break fairly soon anyway and changing two is only about $50 more than changing one, and because the springs on both sides should be of equal stiffness - if not, then the door will be unevenly weight compensated and try to open cockeyed, increasing wear and risk of damaging the motor. http://www.youtube.com/v/Z_eZc-kh40c
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Hello. We have a gas furnace no pilot light and it turns on but no hot air blows. The fan works when switched to On (instead of auto) but won't blow on heat. Any ideas? We've had gas and repair people in and they can't diagnose the problem. It happened last year and then stopped without a diagnoses and started doing it again exactly a year later :(
SNAP... bang... boom. That is the sound of a garage door torsion spring breaking. It can be a very loud noise that sounds like a firecracker or gunshot. Springs are rated for a certain number of cycles and are the first thing that will break in your garage door assembly. Broken springs are the #1 source of customer calls for garage door repair companies. If you have a broken spring, you should NEVER try to open the door, as it can be very dangerous. This repair should be left to a professional or someone with the right tools and skills.

Hello. We have a gas furnace no pilot light and it turns on but no hot air blows. The fan works when switched to On (instead of auto) but won't blow on heat. Any ideas? We've had gas and repair people in and they can't diagnose the problem. It happened last year and then stopped without a diagnoses and started doing it again exactly a year later :(
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
So your garage door is acting up, but you aren’t sure what the problem is. Maybe the door spring is one possible culprit, but you’re not sure if that’s actually the problem or if it’s something else. In this quick list, we’ll go through the most common broken garage door spring symptoms. If your garage door is exhibiting one or a few of these symptoms, there’s a good chance it’s broken and needs replacing.

Garage Door Repair Centennial 80015


You garage door is one of your primary entrances to your home so you want to know that they are functioning properly at all times. If you are having complications with your current garage door, then you need to hire a professional garage door company to determine if it needs to be repaired or replaced. Included are the average garage door repair costs in 2019, for the United States. I’ve also included some garage door repair costs pictures, graphics and graphs that include high, low and average costs for garage door repair, installation and replacement costs. It also includes garage door part repair and replacement costs.
6.7 It's now time to unwind the spring. Firmly position yourself on a steady ladder beside the garage door. Next, insert the bar into one of the holes of the winding cone. Make sure it goes all the way in. It should click when your bar hits the core. If you want to test the force you will be handling before loosening the set screws, push up on the bar one quarter turn and bring it back down. Next, while grasping the other end of the bar firmly, loosen the set screws with an open-end wrench or small adjustable wrench loose enough to come free should the cone spin. Be prepared for the torque to be transferred to the bar.
×